PROBLEM O9: Two cast-iron pipes are held together by a bolt, as shown in fig. The outer diameters of the two pipes are 50mm and 70mm and the wall thickness of each pipe is l0mm. The diameter of the bolt is 15mm. What is the maximum force P this assembly can transmit if the maximum permissible stresses in the bolt and the cast iron are 200MPA in shear and 150MPA in tension, respectively? P

PROBLEM O9: Two cast-iron pipes are held together by a bolt, as shown in fig. The outer diameters of the two pipes are 50mm and 70mm and the wall thickness of each pipe is l0mm. The diameter of the bolt is 15mm. What is the maximum force P this assembly can transmit if the maximum permissible stresses in the bolt and the cast iron are 200MPA in shear and 150MPA in tension, respectively? P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: i- The Mechanical system shown in Fig. 4 is called? ------ Fig. 4. a- Symmetrical Mechanical system.…

A: (i) Answer = (b) Two force member Since in two force member the line of action of force will always…

Q: Punch Aluminum =4 mm d-20 mm

A: Given that t=4 mmd= 20 mmUltimate shear stress = 280 Mpa

Q: Is this a frame or a truss? Calculate the cross section of the bar BC if the allowable normal stress…

A: Given:- Allowable normal stress in BC = 165 MPa To determine- a) Is this a frame or a truss? b)…

Q: 3. The figure as shown below is a rigid bar which is supported by two rods and a pin support. If the…

Q: In the figure shown, determine the normal stresses at AD • and BC • shearing stress at bolt D • ,…

A: Calculation: The moment at point C can be calculated as, ∑MC=0200.25+0.4-RD0.4=013-RD0.4=0RD=32.5 kN…

Q: B F 12 ft 8 ft 8 ft 12 ft 12 ft E G 12 ft 12 ft 1200 lb 1200 lb 1200 lb

Q: 18,000 lbs K₁ 3) This steel bar is 3" x 3" by 30" long. It has a 1" diameter hole centered in the…

Q: HW A rigid Sslab weighing boo Ku is Placed uPon two bronzevads and one Steel Vocd Cach of bo00 mm²…

A: Given data, Weight = 600 kN Area of bronze rod Ab = 6000 mm2 Coefficient of expansion for steel αs =…

Q: SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the…

Q: The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90…

A: To find deformation in member CG and FG

Q: Determine the force in the most stressed bolt of the group shown in figure (2) using the elastic…

Q: Cg Methed f Sectins loo kw determine forces in FE, FC bC ノ

A: Hello dear this is the solution of your problem The answer is found to be Force in members…

Q: The plates in the figure below are each 3 inches by 0.5 inches in cross section. If the hole in each…

A: Solution:- Given information: Cross section of plate =3×0.5 in Hole diameter, d=1316 in, and Load,…

Q: NE THE FORCE (Ib) E DATA BELOW:

Q: hown in the figure. The properties of the segments and the work ble. Determine the maximum allowable…

A: Solution: For compound bar (Steel section) Ast=0.75in2Est=30×106 psiLst=2×12=24…

Q: AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGTHS SHOWN IN THE FIGURE. IF E = 85 KPa, COMPUTE THE…

Q: need the answer quickly

Q: In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a…

Q: The lower ends of the 3 bars in the figure are at the same level before the rigid homogenous 18Mg…

A: Find the stresses developed in each bar.

Q: The thin uniform plate shown has a mass of 100 kg and is subjected to a force and couple moment…

Q: Axial loads are applied to the compound ro composed of an aluminum segment rigidly connected between…

Q: SIMPLE STRESSES 340 mm 1. Two plates are connected by bolts as shown in the figure. Compute the…

A: To determine the bearing stress in each bolt. Given, Diameter of each bolt (d) = 20 mm Magnitude…

Q: Part A If the bolt is subjected to a compressive force of P = 21.9 kN, determine the magnitude of…

A: Length of bronze and steel rod is same.The change in length of steel is equal to the change in…

Q: Q3: For the assembly shown in Fig. Q3. Axial loads are applied at the positions indicated. Find the…

Q: Determine the stresses in the steel rod and copper tube if the temperature rises from 15 C° to 70…

Q: Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter…

Q: The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor…

A: Given Data: d=10mm Stress,s=250Mpa FOS=2

Q: 12 ID 12 Draw the Mohr's circle. Find the stresses on the plane shown. Fill in the blanks and table.…

Q: : Fig. 2 shows a rod consisting of three segments, each having a circular cross- sectional area, is…

A: The answer are given in step by step format Formula used - Stress = Force / Area

Q: Determine the deformation of the steel rod (inches) in the figure shown under the given loads Given:…

Q: A brass bar is fastened between a steel bar and an aluminum bar as shown in the figure. Axial loads…

Q: a) Calculate the greatest tensile and compressive stresses occurring in the section a-a shown in the…

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

100%

PROBLEM O9: Two cast-iron pipes are held together by a bolt, as shown in
fig. The outer diameters of the two pipes are 50mm and 70mm and the wall
thickness of each pipe is 10mm. The diameter of the bolt is 15mm. What is
the maximum force P this assembly can transmit if the maximum permissible
stresses in the bolt and the cast iron are 200MPA in shear and 150MPA in
tension, respectively?
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
P(kN) 53 A 3 3 find S1,52,53,54, S5 Rod forces.indicate that they are tensile or pressure.Write the results you found in the table below. www ww wm w w ROD FORCE TENSİLE/PRESSURE NUMBER S1 S2 S3 S4 S5 5u
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
Please show a detailed solution and explanation including its FBD. Thank you!
Topic: Stresses in Beams (Given formulae: Fb =Mc / I for bending stress v = VcA' y' / Ib for Shear stress)
Read the question carefully and give me all right solutions with clear calculations.
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)
A steel latch is 6 mm thick. A force F of 3000 N is uniformly distributed as shown below. Do not consider the stress concentration! a) Determine the principal stresses at Scction B-B?. b) Determine the principal stresses at point A? 3 kN Y R30 L, A 125 09
In the given system rod lengths are LAB = 5m, LBc=3m and the angle attached to the horizontal of the AB rod is a = 37°. The cross- sectional areas of the rods are A = 15 cm’and Anc = 20 cm and the modulus of elasticities of the rods are E=80 GPa and EBc=100 GPa LAB , A AB Luc, Apc В C a) Calculate the stresses that will occur in the bars. 20 kN b) Calculate the horizontal and vertical displacement at point B.
Read the question carefully and give me both right solutions with clear explanation. Don't copy from other websites solution
PLEASE DRAW THE FBD. DO NOT COPY YOUR ANSWER FROM OTHER. I WANT TO SEE THE FBD OF INDIVIDUAL DEFORMATIONS ON HOW YOU WILL ARRIVE ON YOUR ANSWER. DRAW FBD ON EACH PLEASE. NOT ONLY ONE FBD