The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.

The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V-belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=900N), coefficient of friction ų=0.3 4- the speed of large pulley.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.160P: If PCD=6000lb and PGD=1000lb (both compression), find P and Q.

See similar textbooks

Related questions

Q: Help Me Please Compute all reactions at the base A of the traffic light standard, given that the…

A: Apply trigonometric identity in ΔABC. Resolve the above free-body diagram.

Q: Draw the free-body diagram of CBA and DB

Q: plane diagram: Also String 1 String 1 B String 2 A The diagram above shows Carts B and C which roll…

Q: The man in given figure is trying to move a packing crate across the floor by applying a horizontal…

A: Data given - W = 250 N P = 60 kN

Q: The forklift weighs 3500 lb and carries an 800-lb shipping container. There are two front wheels and…

Q: 350kN F N

A: When two surfaces are sliding or trying to slide over another, friction forces act between them.…

Q: The rope and pulley system shown in Figure 1 has 80- and 90-lb weights attached to ropes. The 80-lb…

Q: 2.) A person uses a force P to keep the pulley system in equilibrium. The mass shown is 10 kg. Note…

Q: Ex.6.4 Compute the acceleration of body B and the tension in the cord supporting A. B. 300 lb 1-0.20…

Q: A 70 lb-bag of rice is being pulled by a person by applying a force F at an angle e. The force…

A: Given data Mass of bag of rice = 70 lbApplied force = FForce is applied at an angle θCoefficient of…

Q: Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a…

A: Diameter of driving pulley, D1=480 cm=4.80 mDiameter of driven pulley, D2=80 cm=0.80 mDistance…

Q: 2.2 A combat aircraft weighing 30,000 lb. is flying in an inside vertical loop [the pilot's head is…

Q: Hello, i am asked to create my own statics problem, here are the specifications. Thank you very…

A: Let a cylinder of mass m and radius r and height h is placed horizontally on vertical support as…

Q: 1-Determine the dof (mobility) of the following mechanisms.

A: Solution: The degree of freedom of a mechanism is the number of relative motions the rigid links…

Q: Q3: Explane in which case Fg has a maximum Value & minimum Value in Pulling the car shown in Fig. 20…

A: given; ⇒lets take net horizontal force in x-directin=P

Q: If a load of 100 N at 45° is to be balanced by another mass kept at twice the radius of rotation as…

A: Given data:

Q: 4. Static. Draw FBD for each mass including the scale. 5 kg 30° 5. Block slides up. 50 P 6. Draw FBD…

Q: Draw free-body diagrams of members AC and BG 3 m -8 m G 2 m 15 2 m 8 2 m A 300 N 3**3**3*

Q: Task 3 Generate free body diagram for the following mechanism: C В 4 m E D 6 m 8 m-

A: The hinge support at E gives the horizontal and vertical reaction. The roller support at D gives a…

Q: The driver attempts to get the car out of the mud by exerting a perpendicular force of 610.0 N, and…

A: Given: The magnitude of the perpendicular force is F=610 N. The free-body diagram is shown below,…

Q: 100 kg

A: Newton's subsequent regulation expresses that the speed increase of an item relies on two factors -…

Q: When a person stands on tiptoe (a strenuous position), the position of the foot is as shown in…

A: force in vertical direction∑Fx=0Rsin 16 - T sinθ=0Rsin 16= T sinθR=Tsinθsin 16 eqn1

Q: etermine the equivalent spring stiffness of the system using the displacement of the block as the…

A: To determine the equivalent spring stiffness of the system.

Q: Draw the FBD and derive the EOM of the pulley system below with respect to x using Ne

Q: The circular shaft of constant cross - section carries three pulleys and belts which are vertical .…

Q: A spring is such that a 5 -lb weight stretches it 6 in. The 5 -lb weight is attached, the spring…

A: Given:Weight on spring=5 lbInitial dsiplacement of spring=x=6 inch=(6×0.0833 ft)=0.5 ftLet spring…

Q: Crate and Wedge The crate weighs 300 lb and ls at all contacting surfaces is 0.3. Assume the wedges…

Q: Arm ABC is connected by pins to a collar at Band to crank CD at C. Neglect the effect of friction.…

A: From the given diagram the point C is a hinge, so it has a horizontal and a vertical reaction, B is…

Q: 6/107 The 180-lb tree surgeon lowers himself with the rope over a horizontal limb of the tree. If…

A: Given data, Weight of the man, W = 180 lb Coefficient of the force between the limb and rope, μ =…

Q: Write the necessary equations of equilibrium of the object shown in the figure below. Take the…

A: Given, Forces = Rx , Ry , Fx and Fy Length = l

Q: high rise building, the elevator rises at a height of 1300 ft with an accelerationof 3.90 ft/s^2 and…

A: Given:h=1300 fta=3.90 ft/s2m=1800 Kgd=16 mmPe=2150 lb

Q: Sketch the free-body diagram of the cylinder.

Q: The cord is attached to the pin at CC and passes over the two pulleys at AA and DD. The pulley at AA…

Q: Q1: The cutter bar of a mower is connected to the P.T.O. shaft of a tractor making 1500 stroke per…

A: There are two types of forces that are acting on a circular surface. One type of force is Radial…

Q: Q1) In the arrangement given in Figure Q1, weight of Q is 1000 N and weight of the platform P is 200…

Q: The reaction forces applied by the unbalanced loads on the shaft to the A and B bearings,FA = 3i N…

Q: orce is acting on the frame as shown in the figure es between 50 and 250 Hz. If friction is…

Q: k, k3 A k2 What is the equivalent spring stiffness between the points A and B. If ki = 1 N/m, k2 = 1…

A: Given:spring stiffness, k1=1 N/mk2=1 N/mk3=2 N/mk4=2 N/m

Q: echanism shown in the figure if the crank 2 is driven at w;=48 d/s ccw. O2|=200 mm, |BA|=800 mm,…

Q: Two blocks of mass Mi and M2 are connected by a massless string that passes over a massless pulley…

Q: 5. The figure below represents the anatomy of the lower limb when balanced on your toes and the body…

A: Given: Mass of the body is 70 kg. Tendon makes an angle of 8 deg.

Q: (11) Ignoring friction, the equation E x ED = R x RD is true for all three classes of levers. Use…

A: In the given lever diagram, hinge is at point D, Load of 100 N is acted at point R and the effort is…

Q: 40 cm. Determine the horizontal anchoring force needed to hold the elbow in place. Figure Q5 (a)

A: For solution refer below images.

Q: 2|A block with a mass of m = 5.5kg, is supported by two massless pulleys as shown to the right →.…

Q: The level of a common steelyard without hook connections weights 7kg and acts at 5cm to the left of…

Q: what is the compression in 2 springs after the block A with 50 N is falling off on it from the rest…

Q: Q1/ For the following write either True or False and correct the false sentences. 1. Static…

A: 1) True Static stability shows the tendency of aircraft to retain its original position when it is…

Concept explainers

Forced undamped vibrations

In mechanical engineering, vibration is expressed as the term that occurs due to an object's backward and forward movement about a point of equilibrium. Generally, there are three types of vibrations which are,

Question

PROBLEM

The diameter of two pulleys are (0.3m)and (0.2m),

center distance (1m).if we use open belt drive.

Determine:

1- the length of V-belt (2ß = 60°).

2- the contact angle between belt and smaller pulley.

3- the horse power, if the smaller pulley turn with

speed (400r.p.m) and the tension force in

tight side (T1=900N), coefficient of friction ų=0.3

4- the speed of large pulley.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If PCD=6000lb and PGD=1000lb (both compression), find P and Q.
The diameter of two pulleys are (0.3m)and (0.2m), center distance (1m).if we use open belt drive. Determine: 1- the length of V- belt (2ß = 60°). 2- the contact angle between belt and smaller pulley. 3- the horse power, if the smaller pulley turn with speed (400r.p.m) and the tension force in tight side (T1=90ON), coefficient of friction u=0.3 4- the speed of large pulley.
Problems 1.35 through 1.41 Find the length of the unknown link so that the linkage forms a crank rocker mechanism and the transmission angle falls between 45 and 135º. 1.35 L = 100 mm, L2 - 140 mm, and L = 120 mm; tind Ly. 1.36 L 50 mm, L2 = 200 mm, and Lo - 210 mm; find L. 1.37 L -110 mm, L= 150 mm, and Lo - 150 mm; find L. 1.38 L/L = 1.5 and LAL - 1.2; find L/L. 1.39 LIL - 3.2 and L L = 1.7; find Ly/L. 1.40 Plot the range of permissible values, if any, of L/L, versus LJL for LIL - 2. 1.41 Repeat Problem 1.40 for LOL = 4.
Q1. Find ( Keq. ) torsional for the system and ( Jeq) about rotation axis of rocker arm. 一

find the mobility and determine the Grashof condition
a) Find the forces in the cables AB, BC, CD, DE, and force in the spring CF in terms of P. (a is an unknown of the problem) b) If the maximum force that any cable can support is Smax, determine the maximum value of P that can be supported. c) If the original length of the spring is ??, find the stiffness of the spring, k.
Five movable pulleys are arranged as in the first system of pulleys. If the efficiency of the system is 80%. Find the effort required to raise a load of 1000kg.
2.22 Calculate the centre distances for a v-belt drive given pulley pitch diameters of 180 mm (motor) and 400 mm (driven) when the belt is (a) an SPÁ 2 360; and (b) an SPB 3 800. [716 mm; 1 441 mm] Calculate the angle of contact on the smaller pulley for both cases. Determine the tension ratio if the groove ang- les are 38° and u is 0,25. (162°; 171
HaW: Find the tension force in each cable. 350 本 A. Oss kg.
Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
T=100 lb W
A truss is facing a two-force member and both of them are in the opposite directions, and the truss is in equilibrium. And both of them are coming to each other. The forces are called Select one: O a. Tensile Forces O b. Compressive forces O c Parallel and collinear forces with same direction of heading O d. The rotational forces Next page est-3 Jump to...