SITUATION 7:The diameter of the pipe is 100 mm andvelocity of oil (SG=0.89) is found to be 3,4 m/s.32. Determine the mass flow rate.a. 23,77kgb. 23.32kgc. 33.28 gd. 22.74 Kg33. Determine the hydraulic radius of the pipe.a. 6 mmb. 3 mmc. 0.025 md. 0.006 m34. Determine the slope if n30.015.a. 0.356b. 0.817c. 0.524d. 0.475

Answered: Image /qna-images/answer/c20c8e14-87f6-4deb-9b6e-2bf5d7850522.jpg

The diameter of the pipe is 100 mm and velocity of oil (SG=0.89) is found to be 3,4 m/s. 32. Determine the mass flow rate. a. 23.77g b. 23.32 g kg c. 33.28 DIL 33. Determine the hydraulic radius of the pipe. d. 22,74 - a. 6 mm b. 3 mm c. 0.025 m d. 0.006 m 34. Determine the slope if n30.015. a. 0.356 b. 0.817 c. 0.524 d. 0.475

The diameter of the pipe is 100 mm and velocity of oil (SG=0.89) is found to be 3,4 m/s. 32. Determine the mass flow rate. a. 23.77g b. 23.32 g kg c. 33.28 DIL 33. Determine the hydraulic radius of the pipe. d. 22,74 - a. 6 mm b. 3 mm c. 0.025 m d. 0.006 m 34. Determine the slope if n30.015. a. 0.356 b. 0.817 c. 0.524 d. 0.475

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discharge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023. Include the diagram in your solution. a.100 kPa b.150 kPa c.75 kPA d.225 kPa
A2: FLUID FLOW, FLOW RATE & PRESSURE DROPProblem:4. Determine the average velocity in m/s for water flow in a 2 in diameter pipe, Schedule 40 chlorinated polyvinyl chloride (CPVC) pipe (2.375 in outside diameter and 2.047 in inside diameter) carrying cold water at a volumetric flow rate of 40 gpm.
A 1.2 m steel pipe 9 mm thick carries water at a velocity of 1.83m / s . The pipe line is 3050 m long and a valve is closed at the discharge end. Bulk modulus of elasticity of water is 2.2 GPa. Determine the maximum rise in pressure in kPa could be expected if valve is shut in 2.5 sec . A. 180.955 Mpa B. 4465.1997 kPa C. 260.234 Mpa D. 1483.240 kPa
6. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a flow rate of 6 L s'. For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of the water gage. Determine the smallest standard commercial steel pipe that will give the required performance. pump 4.5 m. 1.8 19=d 3.5 m 7. water 90° elbow
Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level of oil in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48 kPa absolute and its specific gravity is 0.82 Determine the NPSH in meters available. choices: a. 19.36 b. 17.23 c. 4.64
3.) Water flow at the rate of 200 lit/sec through 120-m horizontal pipe having a diameter of 300 mm. If the pressure difference between the end points is 280 mmHg, determine the friction factor Answer: 0.0233 Subject: fluid mechanic Lesson: *Conservation of Energy *Fluid Flow in Pipes
FLUID MECH Support your answer with the appropriate solution and diagram. 9. At point A in the pipeline conveying water, the diameter is 1 m, the pressure 100 kPa and velocity 1 m/s. At point B, 2 m higher than A, the diameter is 0.5 m, the pressure is 20 kPa. Determine the head loss in m. A. 5.0 B. 5.4 C. 5.8 D. 6.2
A 10-in. x 6-in. x 12-in. duplex direct-acting steam pump operating at 35 strokes per minute delivers water at a temperature of 150 F. If the slip is 7%, determine the a. discharge in lb/hr b. discharge in gpm
A pipe, inside diameter 1.27 cm, water flows through the pipe at a rate of 0.5 liters per second at 20 C. a. What is the velocity of the water (average) in the pipe? b. What is the Reynolds number value? c. Is the flow laminar or turbulent?
9. The diameter at section (1) is 0.3m. The diameter at section (2) is 0.15m. What is the flow rate of a substance (sp. gr. = 0.85) if the pressure between sections (1) and (2) is 12.7 cm Hg?
Please provide complete solution and diagram. An air compressor takes air and discharges it to 200 psi. If the volume flow of the discharge is 1.5 m3/sec, determine the capacity of the compressor in liters per sec. A. 9570.23 li/s C. 9680.24 li/sB. 8680.25 li/s D. 9750.24 li/s
Water enters through a 500 mm diameter inlet pipe under a pressure of 15 kPa. It leaves through a 1000 mm diameter exhaust pipe with a pressure of 5 kPa. If the center of the outlet pipe is 3 m above the center of the inlet pipe and 500 L/sec of water passes a motor or pump. Which of the following most nearly gives the specific gravity of the block? a. 1.6320 b. 0.6814c. 0.3196 d. 1.3186