A water tank with a capacity of 1500 L is desired to be completely filled in about 1.5 hours. The total length of the suction and discharge pipes are 7.1 m and 12 m, respectively. All pipes uses 2 in.-diameter PVC pipes (ɛ = 0.15 mm). The elevations are shown in the figure below. Calculate the power input (in kW) to the pump if pump efficiency is 86% and motor efficiency is 96%. Take the density of water to be 1000 kg/(m^3) and p = 1.00E-3 Pa-s. 18 m 6 m Round your answer to 4 decimal places.

A water tank with a capacity of 1500 L is desired to be completely filled in about 1.5 hours. The total length of the suction and discharge pipes are 7.1 m and 12 m, respectively. All pipes uses 2 in.-diameter PVC pipes (ɛ = 0.15 mm). The elevations are shown in the figure below. Calculate the power input (in kW) to the pump if pump efficiency is 86% and motor efficiency is 96%. Take the density of water to be 1000 kg/(m^3) and p = 1.00E-3 Pa-s. 18 m 6 m Round your answer to 4 decimal places.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A water tank with a capacity of 1500 L is desired to be completely filled in about 1.5 hours. The total length of the suction and discharge pipes are 7.1 m and 12 m, respectively. All pipes uses 2 in.-diameter PVC pipes (ε = 0.15 mm). The elevations are shown in the figure below. Calculate the power input (in kW) to the pump if pump efficiency is 86% and motor efficiency is 96%. Take the density of water to be 1000 kg/(m^3) and μ = 1.00E-3 Pa-s.
In the system given below, the water taken from the A chamber is transmitted to the D chamber with the help of the pump at the C point. The power of the pump at the C point, the local loss coefficient due to the valve at the B point and other data are given in the table. How many meters (m) is the elevation difference between these two reservoirs? Hopper-Pipe connections are sharp (90⁰ junction). Note: The Colebrook-White equation will be used in the solution. Kinematic viscosity value will be taken as 1.13x10-6 m2 / s. please fast help
Q1) Figure Ql shows piping system with pump to drive the oil upward from A (P=PA kPa) to B (P=180 kPa) at a mass flow rate of 3 kg/s. Determine type of flow and calculate required pump power. Given data: oil density and viscosity are 891 kg/m³ and 0.29 N.s/m² respectively. Use Hagen Poiseulli equation for loss: he128µQL/(xpgD“) and Power=Qpghr; Triangle geometry: a²=b²+c² Dripe = 3 mm 15 m Pump 20 m Figure O1
10.0 m 200 m 2. An old western town has a water tower to deliver water to the residents. Pictured above is the water tower. The water tower is closed but there is a section of air that is atmospheric pressure just above the water. The corsss ectional area at point 2 is 4.75 x 10 m. The cross sectional area fot the water tower is very large. What is the speed of the water coming out of the pipe at point 2? (density of water = kg/m³) 3. On a vacation trip up in Oregon my boys decided to build a 10 kg raft that they made out of driftwood. 1000
A pump has an efficiency of 65%. It is driven by a 0.75 horsepower motor. The pump produces a pressure rise of 0.0174 psi in water. What is the required flow rate in cubic meter per second?
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 108 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument) as 0.9 and sp. gr of oil = 0.8 Difference in pressure head (unit in mm) = Velocity of flow (unit in km/hr) =
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 112 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.92 and sp. gr of oil = 0.8 %3D (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in m) = Velocity of flow (unit in m/s) =
Q2- A (0.14 m/s) oil has (density 880 kg/m³ & viscosity 0.026 pa.s) is pumping from first tank to second tank by using centrifugal pump and discharge pipeline 12 inch in diameter. If the pipe roughness is 0.045mm: 1- Calculate pipe frictional head loss for discharge pipe 6100m in length. 2- Calculate pump liquid power if oil level in first tank 7 m, the oil level in second tank is 14 m, and the suction pipe length is 53 m and diameter is 14 inch.
A fluid at a certain temperature has a viscosity of 36.52 cP and a specific gravity of 0.8565. 56324.4 bbl of this fluid per day is transferred from a far-flung source 525.44 miles away using a 23.02 ID steel pipe. Given that the pump has an efficiency of 80.37%, what is the actual power requirement in kW. i. 4105 ii. 3959 iii. 444 iv. 8059 v. 4268
A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a manufacturing plant. The pump operates against a head of 30 m and has an efficiency of 70%. If this pump is situated 9 m below the level of the source, calculate (Zs)max and determine if the pump is safe from cavitation. Select one: O a. -7.9 m; NOT SAFE O b. -9.7 m; NOT SAFE O c. -7.9 m; SAFE O d. -9.7 m; SAFE
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 110 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument ) as 0.9 and sp. gr of oil = 0.9Difference in pressure head (unit in m) =Velocity of flow (unit in m/s) =
Q2- A (0.14 m/s) oil has (density 880 kg/m & viscosity 0.026 pa.s) is pumping from first tank to second tank by using centrifugal pump and discharge pipeline 14 inch in diameter. If the pipe roughness is 0.045mm: 1- Calculate pipe frictional head loss for discharge pipe 6100m in length. 2- Calculate pump liquid power if oil level in first tank 7 m, the oil level in second tank is 14 m, and the suction pipe length is 55 m and diameter is 16 inch.