Quest Air (at atmospheric pressure) at a day bulb temp.anof 40°c and wet bulb temp. of 20°℃ is humidifiedinair washer operating with continuouswater recirculation. The wet bulb depressionthe exif is 25% of that at theindetThe day bulb temperature at the exitof the air washer is ?at

Given data; Air at atmospheric pressure; Wet bulb temperature, WBT=200C Dry bulb temperature,…

Answered: The day bulb temperature at the exit

Engineering

Mechanical Engineering

The day bulb temperature at the exit

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter48: Cooling Towers And Pumps

Section: Chapter Questions

Problem 2RQ: The typical difference in temperature between the cooling tower water supplied to the condenser and...

See similar textbooks

Related questions

Q: What is the relation between modulus of elasticity and modulus of rigidity.

A: Modulus of Elasticity:- The slope of stress-strain curve under direct loading is called Modulus of…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A: Given data: F1=20 kNF2=20 kNF3=10 kNF4=50 kNM=145 kN.m Need to determine the equation of line of…

Q: Product of mass and velocity called linear momentum T O F O

Q: Can you calculate the work done if .the forces are non conservative

A: 1) A conservative force is one for which the work done is independent of path. 2) A force is…

Q: If the resultant of the loads shown passes through point B, determine the equivalent force-couple…

Q: P₁ = 10 MPa •T₁ = 600 °C 2 21 A. For the turbine, for mass flow rate of 3,000 kg/hr, calculate: 1.…

Q: The L-shape frame shown in Figure 2 is fixed and supported at point A and experienced multiple…

Q: * Fixed-Fixed bar was 20 centigrade degree at room temperature, Determine the thermal stress when…

A: Given data as per the question The initial temperature of the bar = 200 c The final temperature of…

Q: 4. The surface of the Sun has a temperature of about 6000 K. At what wavelength does the Sun emit…

A: when a wave form signal from any source propagte in the space or through the wire, then the distance…

Q: Two plates are a length (L) and thickness (t). were welded together. Assume these plates have…

A: When two plates of same length and thickness are joined together using welding, the lap joint would…

Q: B=56 inside diameter = 66 in. wall thickness=0.23 in. allowable normal stress perpendicular to the…

Q: A printed circuit board with constant surface temperature dissipates 100 W from one side over an…

A: Introduction: The change in temperature is connected with heat transmission. The heat transmission…

Q: are 3 methods that can be used to control the metal flow under the blank holder in deep drawing…

A: Drawing is a metalworking technique that involves stretching metal, glass, or plastic by applying…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 2000 mm² and an…

A: Answer: The maximum load that can be supported by the structure without exceeding either allowable…

Q: Calculate the Net Positive Suction Head (NPSH) for a pump handling 100,000 kg/hr flow of water…

Q: The 480-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

Q: C- A rigid 1 m³ tank contains nitrogen gas, initially at 10 bar, 27 °C. Heat transfer to the gas…

A: Write the given data. V1=1 m3P1=10 bar=P2T1=27 °C=27+273=300 KT2=400 K

Q: Four people are attempting to move a stage platform across the floor. If they exert the horizontal…

Q: What’s the formula for finding center of gravity when thickness is included

A: center of gravity is a point where we considered that the weight of a body is acting. In uniform…

Q: Determine the force in each member of the loaded truss as a result of the hanging weight W = 205 lb.…

Q: 1. Find the precision value of X1 and X2? X₁ = 101 X₁ =98 X₂ = 98.5

A: Given data: Xn = 101X1 = 98X2 = 98.5 We have to find the precision value of X1 and X2

Q: Determine the speed v which the 525-kg four-man bobsled must have in order to negotiate the turn…

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

Q: Given the FLEXURAL RIGIDITY=6000 :KN.m^2. The deflection value at point A is 50 kN A 9m B

Q: Can you calculate the work done .the forces are non conservativ Yes No

A: Work for a nonconservative force is contingent on the path pursued. Friction is a nonconservative…

Q: A cylinder is to be tested by Engr. Dejesa using two working fluids. The working fluids are oxygen…

Q: The simply supported beam as shown in Figure 1 has the rectangular cross-section (b = 85 mm, h = 105…

Q: The combined action of the three forces on the base at O may be obtained by establishing their…

Q: In rectilinear motion of a particle, the work is equal to the change in the .kinetic energy of the…

A: Work energy principle for rectilinear motion, For particle if it performs rectilinear motion under…

Q: Two air streams at standard atmosphere are mixed adiabatically with the first air stream at 15°C db,…

Q: .) How many different types of welds are specified on the print and what are they? (Hint: look at…

A: Welds come in a variety of shapes, which are best defined by their cross-sectional form. The fillet…

Q: (9) Find the angle between two vectors: A=31+4j-5k, (1) Scalar product. (2) vector product. B =…

Q: Please can you explain how the concepts of the kinematics of rigid bodies are related to position,…

A: Introduction: A rigid body is a perfect representation of a body that does not deform or alter its…

Q: Moist air initially at standard atmospheric pressure, 15°C db, 70% relative humidity undergoes a…

A: Note: As per the policy, we can solve the first question from multiple questions. Please resubmit…

Q: Air initially at 101.325 kPa, 30°C db and 40% relative humidity undergoes an adiabatic saturation…

Q: With the assumption of no slipping, determine the mass m of the block which must be placed on the…

Q: pective Gears Q and Rare mounted on the same shaft as shown in the figure below. The diameter of the…

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 7 mm2.…

Q: Determine the maximum load P that can be safely carried by the titanium bar. The factor of safety is…

A: Given f=2 allowable stress of titanium =240MPa

Q: what should be its diameter? Also find the length of the middle portion, if the total extension of…

Q: B-A Refrigerant 134a is contained ank of volume 0.2 m³. Initially the refrigerant exists in a…

A: Given Data The volume of the tank is: V=0.2 m3 The initial temperature of the refrigerant is:…

Q: What is the specific heat of metal if its mass is 27 g and it requires 420 J of heat energy to…

A: Dear student, as per the given data, there is no correct option. Please find the attached solution.…

Q: An object of mass 1000 kg, initially having a velocity of 20 m/s, accelerates to a final velocity of…

Q: forming temperature condition. 8) In blanking operation, if the final blank diameter is 200 mm & the…

Q: Find the value of Maximum shear stress in rectangular section Shear force-40 N Area of section=2 mm2

A: Given data : Shear force V=40 N Section=Rectangular Area of section A=2 mm2

Q: B. For the cycle, calculate: 4. Network, W in KW 5. Cycle thermal efficiency, e.

A: For the Rankine cycle, Turbine inlet conditions are P1 = 10 MPa, T1 = 600 oC Condenser pressure =…

Q: * For the cross section shown in the figure. :Find the value of Y 40 mm A1 250 mm

A: Given

Q: SHL P Type here to search <-CFD-Hue Pape cice E Ⓒ1038 Question 11 S ACal Can X A Which of the…

Q: Find the value of Maximum shear stress in rectangular section Shear force-40 N Area of section=2 mm2

Q: 40 mm 220 mm For the cross section shown in the figure. Given the value of Y= 172 mm. Find the…

Concept explainers

Properties of Pure Substances

A substance with fixed chemical composition throughout is called a pure substance like water, air, and nitrogen. A pure substance does not have to be a single element or compound. A mixture of two or more phases of a pure substance is also a pure substance as long as the chemical composition is the same for all phases. These substances mainly have a constant/ uniform composition. The substances also have fixed boiling and melting points. A pure substance takes part in a chemical reaction to form predictable products.

Question

Quest Air (at atmospheric pressure) at a day bulb temp.
an
of 40°c and wet bulb temp. of 20°℃ is humidified
in
air washer operating with continuous
water recirculation. The wet bulb depression
the exif is 25% of that at theindet
The day bulb temperature at the exit
of the air washer is ?
at

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pls. Answer thank you! Water at 55°C is cooled in a cooling tower which has an efficiency of 65%. The temperature of the surrounding air is 32°C dry bulb and 70% relative humidity. The heat dissipated from the condenser is 2,300,000 KJ/hr. Find the capacity in liters per second of the pump used in the cooling water
Pls. Answer thank you! The moisture removed from a material is 200 lb/hr and change of humidity ratio in dryer is 0.015. Determine the fan capacity if specific volume of air entering is 38 ft3/lb.
(4) all öf th (b) dry saturated liquid refrigerant The refrigerant supplied to a compressor must be (a) superheated vapour refrigerant (c) a mixture of liquid and vapour refrigerant (d) none of these ant compressor is called
าา 3.15.) In air conditioning unit, 71,000 cfm at 80'F dry bulb 60% th and standard atmospheric pressure, enter the unit. The air leaves the wait at 57°F dry bulb and 90% relative humidity. Calculate the following a.) Cooling capacity of the air conditioning unit, in Btu/h 6.) rate of water removal from the unit. (.) sensible heat load on the conditioner, in Btu/h di) latent heat load on the conditioning in Blu/h e.) The dew point of the air leaving the conditioner.
How high a relative humidity must a 35°C air have in order to obtain saturated airat 18°C by evaporative cooling? solve with complete diagram
your A bank of 120-employees is maintained at 24°C db and 50% RH. The heat gain due to heat transfer through walls, roof, ..etc is 10 kW. The outside air temperature is 35°C and its relative humidity is 60%. Calculate the followings: (a) Ventilation air required. (b) Sensible and latent heat gains due to occupants. (CLF = 0.86) (c) Volumetric flow rate of supply air if the supply temperature is 18°C. (d) Volumetric flow rate of moisture removed. (e) Sensible heat ratio of the theater. (f) Relative humidity of the supply air
Solve the following problems Find the properties of moist air for the following using psychrometric chart: (1) D.B.T. 35 °C W.B.T. 20 °C
QUESTION 1 Water at 60°C leaving a condenser at the rate of 22.5kg/s is sprayed into a natural-draught cooling tower and leaves it at 27°C. Air enters the tower at 1.013bar, 13°C and 50% relative humidity and leaves it at 38°C, saturated. Take Cp for the superheated vapour as 1.86 kJ/kgK. Calculate: 1.1. the air flow rate required in m/s; 1.2. the make-up water required in kg/s.
For an office building the outdoor design condilions are 45°C dbl and humidity ratio. of G.015. The indoor design conditions are 25°C dbl and 0.01 humidity ratio. The supply air slale is 15°C dbl and 0.007 humidily ratio. Il the supply air flow rate is 1000 m/min and fresh air flow rate is 100 m/min, room sensible and room lalent heat loads are, respeclively.
Evaporator single effect is used to upgrade the concentrate 10000 kg/h of tomato juice than 5% solids the total to 30% solids total. Juice enters the Evaporator at 15 °C. The Evaporator is operated with Steam (quality 80%) in 143.27 kPa. The condition of vacuum in the Evaporator allow the juice to a boil on the 75 °C. The hot kind of material dilute is 4.1 kJ/(kg °C) and the product the concentrate is a 3.1 kJ/(kg °C). Count a. The Rate of the needs of steam = ...kg/h. b. The economic steam if the temperature is condensate is released at 75 °C. = ...(kg water evaporated/kg of steam)
What should be the percent increase of COPof a standard vapor compression refrigerationsystem when expansion of R-12 is isentropicinstead of isenthalpic process? Evaporator andcondenser temperature limits are -10°C and30°C respectively.
Exercise 17.5 Air is being drawn over the cold surface of the cooling coil of an air conditioning unit. If 10 m/min enters the air conditioner, calculate the mass flow rate of the condensed moisture, given that the air enters at 20°C and 70% relative humid- ity and exits at 12°C dry bulb temperature and 90% relative humidity. Calcu- late the refrigeration capacity of the coil in W and Btu/h. Solution Step 1 Draw the process diagram: ma ma W; H. H