The current source in the circuit shown in in Figure 1 is iş(t) = 30 cos(314t) A a) Constrict the frequency-domain equivalent circuit. b) Find the steady state expressions of v(t),i(t),, i(t)2 and i(t)3 c) Determine the power delivered by the source to the loading elements. 20ng 10n 10mF 2H3 Figure 1

The current source in the circuit shown in in Figure 1 is iş(t) = 30 cos(314t) A a) Constrict the frequency-domain equivalent circuit. b) Find the steady state expressions of v(t),i(t),, i(t)2 and i(t)3 c) Determine the power delivered by the source to the loading elements. 20ng 10n 10mF 2H3 Figure 1

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

1 In the system shown in the below figure, the switch is closed at t = 0. a Determine voltage reflection coefficient at the load and the source b. Sketch the bounce diagram of the VOLTAGE and the CURRENT and give sufficient information on it (up to 4us) C. Sketch diagram of voltage and current at source and load Mittetu Md. Calculate the steady state Vss. Vss and Iss. Iss opinti 15 Wan httons e. Find the value V(z-50m 1.7us) TERS Wertens atom Dett th will MARRI E yo w B pinn WERS THIS Suprin 90 MAKEL R₂=90 0 3 CAP 180. Rr = 180 Q - i T Mart 1800 H SUS Vg=90 V HIE 1 D = min 200 thin 1 FARG - Bilare. Radio T 149 SATISH SET Pan PARACHUNG G IN Sulta Ap 135 aytinius - FORES exotic Me GALER 2 Mer t=0 400 NITINE atas Aper SUMB satan THE SIM- " WAS Thy POST ANE nicht www.M upp 6 HIS 328 20 p Hifiq Z. = 60 52 WHAT p=10m/s 459 w 30 Patie SATE 108 1 = 100m MNA A
In the circuit shown in the figure, there is a load between the terminals a and b, consisting of the series connection of the resistor R0 and the inductance L0. The amplitude of the voltage Vs (t) is two root hundred and fifty phase angle Qs = zero degree period T = 200 PI microseconds. Since R = 300 ohms C = 1 nano F. a) Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit b) Calculate the complex power on the load.
Given the circuit, solve for:a. Total currentb. Total apparent powerc. Total real powerd. Total reactive powere. pf of the circuitPlease, I need a complete solution. I promise to give it a thumbs up! :)
Calculate the steady-state errors that will occur if the following test signals are applied to the system given in the figure.a) 15u(t)b) 15tu(t)c) 15t2u(t)
In the circuit in the figure, there is a load consisting of the series connection of the resistor R0 and the inductance L0 between the terminals a and b. The amplitude of the VS (t) voltage is √2 150 volts, phase angle = 0 degrees, period T = 200π microseconds.Since R = 300 ohms and C = 1 microfarad a)Find the values of R0 and L0 that enable the load to draw maximum average power from the circuit when the load phase angle is constant at 45 degrees? b)Calculate the average power on the load?
1. For the circuit in Figure 1: a) What is the RMS-value, zero-phase angle and frequency of voltage source e(t)? b) What is the total impedance of the circuit? c) Calculate frequency domain voltage Uc and current lot. (present solution in polar form x < yᵒ). d) Calculate time domain voltage uc(t) and current io(t) (present solution as sine-wave function of time) e(t) = 170 sin (100лt + 25°) V, R1 = 102, C = 15 µF 12 e(t) (1) Figure 1. T 1 ↑ U tot H R UR C HH U₁
A 50 Hz, alternating voltage of 150 V (rms) is applied independently to: (a) resistance of 10 ohms,(b) inductance of 0.2 henry’ and(c) capacitance of 50 microfarad. Find the expression of the instantaneous current in each case. Draw the phasordiagram in each case.
Question 17) Read the question carefully and make your solutions. According to the figure given below, Find the steady-state expressions for the currents and in the circuit in figure when Vg=200cos(800t). 8002 240 mH 400 mH 400 mH M 100 Q
Problem #1) Given the following DC circuit that is operating at steady-state: MW 24V IDC 60 Ohms 100 + Ohms 40uF Determine IDC and VR in the circuit as shown VR 120 Ohms 20mH
In the figure below, all impedances are in ohms, all voltages are in volts and currents in Amperes. Both sources operate at 60 Hz. X, = 200 n X, = 600 n 80 sin (wt + T/2) x, = 600 2 0.2 ain wt Determine the time dependent current i (A) due to the current Choose... source Determine the time dependent current (A) flowing through the inductance with a Choose... reactance of 200 Ohms due to the current source Determine the time dependent current i (A) due to the voltage Choose... source Choose... Determine the total effective current (A) flowing through the Choose... inductance with a reactance of 200 Ohms
2. Using your values for Vps, Vind, VR, Vr, and V₁ from the Data and Calculations Tables above, construct and draw phasor diagrams on the attached graphical page below for each of the LR1, LR2, LR3, and LR4 circuits in Part 2. Be sure to appropriately label ALL the rms potentials.
A 50 Hz, alternating voltage of 150 V (rms) is applied independently to: (a) resistance of 10 ohms, (b) inductance of 0.2 henry' and (c) capacitance of 50 microfarad. Find the expression of the instantaneous current in each case. Draw the phasor diagram in each case.