The cross-sectison of a simply supported plate girder is shown in figure. The loading on the grider is symmetrical. The bearing stiffeners at supports are the sole means of providing restraint against torsion. Design the bearing stiffeners at supports. with minimum moment of inertia about the center line of web palte only as the sole design criterion.

The cross-sectison of a simply supported plate girder is shown in figure. The loading on the grider is symmetrical. The bearing stiffeners at supports are the sole means of providing restraint against torsion. Design the bearing stiffeners at supports. with minimum moment of inertia about the center line of web palte only as the sole design criterion.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.4P: A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are...

See similar textbooks

Similar questions

A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
Answers: AB = kN E AH = kN Determine the force in each member of the loaded truss. All triangles are 3-4-5. Enter a the member is in tension, negative if in compression. BC - kN C 34kN kN BG E 34 kN BH - kN 15 kN BI = kN D B kN kN A E DE kN H G F DF = kN - 4 panels at 8 m- DG = kN DI kN EF = kN FG - kN GH = kN
Each bar of the truss has a rectangular cross section, 30 mm by 60 mm. Determine the maximum vertical load P that can be applied at B if the working stresses are 100 MPa in tension and 80 MPa in compression. (A reduced stress in compression is specified to reduce the danger of buckling.) B 8m Gm 10m
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
Determine the force of the members for the space truss shown in the figure. Joints A and B are supported by ball-and-socket while Joint C is supported by short link along z-axis. Indicate whether member is tension (T) or compression (C). 2m y Sm Az By BX Bz PAR Ax CSXScanned with Ca canner a SISU KN 15m 1 2117
Design any one tension member from the truss shown below. Dead load D = 35 k and live load L = 40 k. Assume U = 1.0. Design using either LRFD or ASD. M A H D B N D E D D 6 at 30 ft = 180 ft K F G D 15 ft 15 ft
7) Determine the force in each member of the truss shown below. C F 100 kips 1S' 1S D - 20 ァー 20
W3D 25 Y= 155 %31 1oow= 2500 KN 27=310mm X= 475 Z= 60 %3D 102=600mm
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co
USE METHOD OF SECTION 2 k 2 k 2 k - 5 ft- 5 ft 5 ft- -5 ft A H F 5 ft C 03. FUND-PROB 037 PPeren Calculate forces in members GF, DG, CD for truss shown above.
1. Determine the force in each member of the loaded truss. All triangles are 3-4-5. Indicate whether it is compression or tension. Use method of joint. C 40KN B XX H G -4 panels at 8 m- A 32 KN 22 KN F D E