A truss tie consisting of 2 ISA 75 x 75 x 8 mm carries a pull of 150 kN. At ends the two angles are connected, one each on either side of a 10 mm thick gusset plate, by 18 mm diameter rivets arranged in one row. The allowable stresses in rivet are f, f = 250 N/mm². = 90.0 N/mm² and

A truss tie consisting of 2 ISA 75 x 75 x 8 mm carries a pull of 150 kN. At ends the two angles are connected, one each on either side of a 10 mm thick gusset plate, by 18 mm diameter rivets arranged in one row. The allowable stresses in rivet are f, f = 250 N/mm². = 90.0 N/mm² and

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a force of 2.5…

A: Given: L= 300mm, d=12mm, F1 = 2.5KN, F2 = 9KN, Change in Length = 0.225mm Determine the modulus of…

Q: Find the stresses ox,, Oy,, and Tx,y, on an element oriented at an angle 0 = 30° clockwise from the…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: The unit of degree of saturation is * kN/m3 True O False O As the volume of mold increases the…

A: The unit of degree of saturation is kn/M3. This statement is False. degree of saturation is ratio…

Q: For the beam l-section below, calculate the second moment of area about its centroidal x-axis…

Q: PERT calculations indicate that duration of a given project is 72 weeks. With the variance of 15,…

Q: An open tank 1.82 m square, weighs 3425 N and contains 0.91 m of water. It is acted upon by an…

A: Given Data: The side of an open tank is 1.82 m. The weight of an open tank is W=3425 N. The depth of…

Q: A 1800kg car travellingvup an inclined 8% grade at a rate of 60 kph and was brought to rest after…

Q: W kip/ft vft Determine the maximum value of w, if oalow = 1000 psi and Talow = 500 psi. 10 ft 4 in.…

A: step 1-

Q: Which of the following is not a property of steel materials? a) Homogeneous and isotropic b)…

A: Steel : When compared to other types of iron, steel is an iron alloy with a few tenths of a percent…

Q: This question is related to building utilities - plumbing and sanitary 1. What are the benefits…

A: 1. When rainwater falls on the ground, it is collected, stored, and used later. It can be purified…

Q: Q1/ Desgin graphically an intermediate casing (11.75-in, set at 6000 ft. Hole diameter26-in. Data…

A: Answer:-

Q: A specific jurisdiction requires a minimum grade of 0.46% to be reached within 19 m from…

A: step 1-

Q: pin (d)

Q: 5- Determine the ultimate moment capacity of the beam shown. Materials; C30, S220 Es= 2x105 N/mm2;…

A: Given Data:Materials:C30,S220Es=2×105N/mmk1=0.85d=52cm=520mmbw=30cm=300mm

Q: barangay hall - design co

A: A barangay hall is the seat of local government for the barangay, the city or municipality's lowest…

Q: 3. Select the lightest W12 section made of A992 steel for the axial loads and moments shown in the…

A: We will use LRFD method

Q: 24 kN 36 kN 18 kN 30 kN 12 kN | | 12 kNm A1=-24(1)=-24 1m 1m 1m 1m 2 m 2 m 3 m "RA=72 kN Re= 48'kN v…

Q: Using the following details, Design the shear reinforcement along the length of the beam if it is…

A: Shear reinforcement is used to withstand shear forces that are greater than the concrete's shear…

Q: Sample description: Uniform SAND, medium grain. Rate of strain: 1 mm/min Proving Ring No. ==…

A: Time (min) Horiz. Displ. (mm) Strain (%) Proving ring Dial (rev) Shear Load (N) Shear Stress (kPa)…

Q: a）For clays, the failure line (one that connects the peak failure stresses) in the normally…

A: A)Cohesion is the stress of binding together, in soil mechanics the cohesion means shear strength…

Q: Define Aseptic Filling Rooms of pharmaceutical industry? Write by your own sentences and thoughts…

A: concept- To protect patients from infection, doctors use aseptic techniques. The Aseptic method is a…

Q: During the shearing phase of a CU test, the void ratio of a NC consolidated clay specimen will:…

A: GIVEN: CU test on NC clay soil is performed. To Find: Variation of Void ratio in Shearing stage.…

Q: The basic differential equation of the elastic curve for a simply supported, uniformly loaded beam…

A: Given Data: w = 15 kn/m L = 3 m E = 200 Gpa I = 30000 cm4

Q: simple curve is ½ of its radius.

Q: You are assigned to a project for the construction of a new tunnel. The tunnel will be 31 feet in…

A: given data tunnel will be 31 feet in diameter 12 thick concrete liner The radial supports will be at…

Q: what does 12”x 12” (300mm x 300mm) with 6 bars of 12mm Fe500 Steel with m20 grade of concrete and…

Q: topic: barangay health center - design concept

A: 1) Barangay health center- It has been welcomed since 1980’s by a few nations as the main functional…

Q: A horizontal curve with spiral is being designed for a new two-lane highway (3.6-m anes and 2%…

Q: A conical tube of length 2 m fixed vertically with its smaller end upwards. The velocity head,…

A: Total head =Pressure head + Velocity head + Datum head. Assuming Datum is at lower end of conical…

Q: Prepare resources allocation planning for smartpen project.

A: Before You Get Started project 1) Know Your Project Team’s Capacity And Availability Before you…

Q: Design and detail a one-way slab both end continuous having span of 6m. The slab is to carry a…

Q: A lap joint configuration is shown below. The bearing stress in the plates is limited to 18 ksi…

Q: . In a 1/50 model of a spillway, the discharge was measured to be 0.3m3 /sec. The corresponding…

Q: 10 in 2. Determine the LRFD Design moment capacity and the ASD allowable moment capacity of a W21X73…

Q: trapezoidal section constant velocity horizontal flow grit channel is discharging unacceptable…

A: grit chamber is provided to remove grit ,organic,inorganic sand conc gravel particles which saves…

Q: If your Pace length is 81 \(\pm ) 4 cm and the total distance measured of a road is 355 pace. Then…

Q: Q3: Shallow footing shown in Figure below calculate the: 文

A: Given, q = 100 kPa μs = 0.30 B = 1 m L = 2 m z = 1m

Q: Determine the largest weight W (in lb) that can be supported safely by the structure shown in the…

Q: 4: A conical tube of length 2 m fixed vertically with its smaller end upwards. The velocity head,…

Q: briefly discuss how the P-Delta effect is accounted for in the design of reinforced masonry walls…

A: reinforced masonry wall : A reinforced masonry wall is constructed using any type of brick,…

Q: H.W: A steel pipe with an outside diameter of 4.500 in. and an inside diameter of 4.026 in. supports…

A: Disclaimer Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: In a 1/50 model of a spillway, the discharge was measured to be 0.3m3 /sec. The corresponding…

A: Given data : Scale model Lr=150 Discharge in model Qm=0.3 m3/s To find : Discharge in prototype

Q: a uniform load w across its full length. Use this beam to respond to problems 4 through 8. 4. The…

Q: An experiment is conducted for infiltration rate under the ponding condition in a soil field and it…

Q: The second moment of area about the centroidal x-axis (IXXcentroid) for the solid homogeneous beam…

Q: Calculate the ultimate moment capacity of a rectangular beam with b = 350mm, d = 540mm, A, =7- 28mm.…

A: Given, b=350 mm d=540mm As=7-28 mm f'c= 24 MPa fy=345 MPa

Q: A rectangular concrete beam has a width of 300mm and an effective depth of 550mm. The cantilever…

Q: Q2) The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure…

A: This question can be solved by applying Bernoulli's equation at 1 and 2. The detailed stepwise…

Q: A village has 1,182 persons. Each person uses 13.4 kWh of electricity per day. They are considering…

A: Answer We are given Village population = 1182 Daily use of electricity = 13.4 Kwh per person Flow…

Concept explainers

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.

Question

A truss tie consisting of 2 ISA 75 × 75 x 8 mm carries
a pull of 150 kN. At ends the two angles are connected,
one each on either side of a 10 mm thick gusset plate,
by 18 mm diameter rivets arranged in one row. The
allowable stresses in rivet are f 90.0 N/mm2 and f
= 250 N/mm2.
Maximum tensile stress in the tie in N/mm2 is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A plate with width of 300mm and thickness of 20mm is to be connected between two plates 12mm thick with same width by 4-25mm diameter rivets a shown. The rivet holes have a diameter 2mm larger than the rivet diameter. The plate is A36 steel with yield strength Fy=248 Mpa and Fu-400MPa. The rivets have nominal shear stress capacity of 165MPa. O 803 O 1490 • Determine maximum load (P1) that can be applied without exceeding design tensile stress in plates (consider yielding and rupture of plates ONLY) in KN O 1180 O 1340 ο ο ο ο ο P3 O 1968 O 590 O 670 O 893 O 707 OO 150 O 1180 P1 P2
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
Q2) One brass bar and one steel bar are forming the setup shown below. Determine the stresses and the strains in the steel and brass bars when a load of 750 kN is applied to the connection of these two members where modulus of elasticities for steel and brass are Est = 200 GPa and Ebr 125 GPa, respectively, and cross-sectional areas for steel and brass bars are Ast = 700 mm² and Abr = 1000 mm², respectively. 500 mm 400 mm Brass Steel F Fixed Support 2 mm Gap F = 750 KN Fixed Support
QUESTION 2 The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in the members when T1 = 50'F, determine the average normal stress in each member when T2 = 120°F Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in? 3 ft 2 ft
The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3,080 mm^2. The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.
Direct Stress Bronze Aluminum Steel A = 0.75 in.2 A = 1.0 in.? A = 0.5 in.? 3P 2F P 4P- -3 ft→ 5 ft 4 ft- 2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Find the largest safe value of P if the working stresses are 120 MPa for steel, 68 MPa for aluminum, and 110 MPa for bronze.
The maximum tension in the wèr link of a Porter governor is 580 N and the maximum stress in the link is 30 N/mm?. If the link is of circular cross-section, determine its diameter.
Problem 912 Compute the stresses at A and B on the link loaded as shown in Figure P-912 if P = 9000 lb and F = 3000 lb. 12 in- 6 in 6 in- 13 in F A 13 in B Figure P-912 -12 in- ¯¯Â 2 in 6 in Cross- Section
A flexural member is fabricated from two flange plates 1/2x16 and a web plate 1/4x20, thusforming a built-up ‘I’ shape member. The yield stress of the steel is 50 ksi.a. Compute the plastic section modulus Z and the plastic moment Mp with respect to the majoraxis.b. Compute the section modulus S and the plastic moment My with respect to the major axis
Determine the force P necessary to close the gap at the steel post. The steel post is 2 inch x 2 inch square and 8 in high. The aluminum alloy bar is 1.5 inch wide by 1 inch thick and 20 in long. The horizontal bar is considered rigid as are the loading caps at the steel post. The modulus of elasticity for the steel is 30,000 ksi, that of aluminum is 10,000 ksi. The yield stress for the steel is 36 ksi, that of the aluminum is 40 ksi. 8" 10" Steel 10" Rigid Aluminum 20 inches long * P 10" Gap = 0.02 inches
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPa, f, = 280 MPa and the net tensile strain is greater than 0.005, then the maximum steel ratio equal............ (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
2. The structure is used to support a distributed load of = 5 kN/m. The bolts at A, B, and C each have a diameter of 16 mm and each bolt is used in a double shear connection. The cross-sectional area of axial member (1) is 3080 mm2.The allowable stress in axial member (1) is 50 MPa and 280 MPa for the bolts. Determine the factor of safety with respect to the specified allowable stresses for axial member (1) and bolt at C.