The cross-sectional dimensions of the beam shown in the figure are a - 4.5 in., b - 6.1 in., d = 4.6 in., andt-0.34 in. The internal bending moment about the z centroidal axis is M, - -3.95 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. (typ.) Answers: (a) OmaxT psi (b) OmayC- psi

The cross-sectional dimensions of the beam shown in the figure are a - 4.5 in., b - 6.1 in., d = 4.6 in., andt-0.34 in. The internal bending moment about the z centroidal axis is M, - -3.95 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. (typ.) Answers: (a) OmaxT psi (b) OmayC- psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part 2,3,4
The cross-sectional dimensions of the beam shown in the figure are a = 4.5 in., b = 5.4 in., d = 4.9 in., and t= 0.31 in. The internal bending moment about the z centroidal axis is M, = -3.85 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. (typ.) Answers: (a) Omax T = psi (b) OmaxC= psi
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If o = 25 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa O 39.2 MPa and -30.2 MPa O 31.6 MPa and -35.8 MPa 54.1 MPa and -41.3 MPa 35.8 MPa and -27.4 MPa O 27.7 MPa and -39.0 MPa Save for Later eTextbook and Media Attempts: 1 of 3 used Submit Answer
Pls show complete solution and fbd
The cross-sectional dimensions of the beam shown in the figure are a = 4.1 in., b= 5.1 in., d= 4.3 in., andt= 0.33in. The internal bending mornent about thez centroidal axis is M, = -4.15 kip-ft. Determine (a) the maximum tension bending stress (a positive number) in the beam. (b) the maximum compression bending stress (a negative number) in the beam. b y |(ур.) |d a Answers: (a) OmaxT psi (b) Omax C= psi
A beam has a concentrated load (Pu) at midspan and has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at 3.19 from the support. (MPa) Properties: Beam width = 211 mm Beam height 389 mm 27 Pu 63.66 kN Span of the beam 8 m Prestressing force 326 kN eccentricity = 95 mm
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
30 mm C A B 150 mm M 150 mm 300 mm 30 mm - determine the bending stress developed at points A, B, and C. Sketch the bending stress distribution on the cross section. - Assume that the cross-section has a moment of inertia about the neutral axis of 1.907 x 10-4 m². - Assume that the neutral axis is located 97.5 mm from the bottom of the cross-section - Assume the internal bending moment M = 61.4 kN.m
Textbook: Statics and Strength of Materials Topic: Axial Shear and Bearing StressProvide step-by-step solutions.
Q.1:Answer only one from a & b: a: At a certain point in a stressed body, the stresses are o, 400 MPa, oy -300 MPa, Txy = 200 MPa and Tx200 MPa. Determine the normal and shearing stresses on the planes with normals are at 25° and 115° clock wise with the X- axis. Show the results on Mohr's circle and complete sketche of defferential element.
The cantilever beam shown has a rectangular cross section with dimensions b = 25 mm and h = 100 mm, and is loaded by a force P that acts at the midheight of the beam and is inclined at an angle a as shown. The beam is made of steel with E = 200 GPa and v= 1/3. Two strain gages are placed at point C, which is also at midheight of the beam. Gage A measures the strain in the horizontal direction and gage B measures the strain at an angle ß= 60°. The measured strains are &a= 125 µɛ, &b = -375 με. Determine: a) The force P in kN [Ans. to check: P = 125 kN] b) The angle a in degrees. B b←
The cantilever T- beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 2.0 m INA = 30x105 mm %3D What is the value of the flexural stress at the Neutral- Axis, NA?