The compound shaft, which is fixed at both ends, is composed of Aluminum shaft ABC (Gal = 24 GPa, d =50 mm), steel sleeve AB (Gst = 76 GPa, dout = 90 mm), and copper sleeve ABC (Gcu = 45 GPa, dout = 75 mm),which are all welded together. Considering the allowable shear stresses (Tal, Ist, Tcu), determine themaximum allowable torque T (kN-m) that may be applied at B as shown.Note: Double-headed arrows follow the direction of the thumb when using the right-hand rule.AParametersTal = 51 MPaTst = 101 MPaTcu = 71 MPasteelCuAIL = 5mB➡TCuAIL= 3.5mC

Answered: Image /qna-images/answer/d8358687-7615-4f8d-936d-62e2a0ce5bf3.jpg

The compound shaft, which is fixed at both ends, is composed of Aluminum shaft ABC (Gal = 24 GPa, d = 50 mm), steel sleeve AB (Gst = 76 GPa, dout = 90 mm), and copper sleeve ABC (Gcu = 45 GPa, dout= 75 mm), which are all welded together. Considering the allowable shear stresses (Tal, Tst, Tcu), determine the maximum allowable torque T (kN-m) that may be applied at B as shown. Note: Double-headed arrows follow the direction of the thumb when using the right-hand rule. A Parameters Tal = 51 MPa Tst = 101 MPa Tcu = 71 MPa steel Cui AI L = 5m B ➡T Cu AI L= 3.5m C

The compound shaft, which is fixed at both ends, is composed of Aluminum shaft ABC (Gal = 24 GPa, d = 50 mm), steel sleeve AB (Gst = 76 GPa, dout = 90 mm), and copper sleeve ABC (Gcu = 45 GPa, dout= 75 mm), which are all welded together. Considering the allowable shear stresses (Tal, Tst, Tcu), determine the maximum allowable torque T (kN-m) that may be applied at B as shown. Note: Double-headed arrows follow the direction of the thumb when using the right-hand rule. A Parameters Tal = 51 MPa Tst = 101 MPa Tcu = 71 MPa steel Cui AI L = 5m B ➡T Cu AI L= 3.5m C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: ber AB consists of a single C130 x 10.4 steel channel of length 2.5 m. Knowing that the pins A ross…

Q: -5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force…

Q: The cmposite beam is made of 6061-T6 aluminum (A) and C83400 red brass (B). The the height, h=40mm,…

A: Section Properties : For transformed section:

Q: Determine the maximum torque T in kN-m without exceeding a shear stre of 70 MPa In steel and 50 MPa…

A: 1. 10.44kn-m

Q: Q.1/The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is…

Q: Problem 3 in the steel structure shown, a 6-mm-diamter pin is used at D and 10-mm-diameter pins are…

Q: 2. The structure is used to support a distributed load of w = 5 kN/m. The bolts at A, B, and C each…

Q: 1. The aluminum rod AB (Ga = 27 GPa) is bonded to the brass rod BD (Gpr = 39 GPa). The portion CD of…

Q: A flanged bolt coupling consists of ten 16-mm-diameter bolts spaced evenly around a bolt circle 650…

A: Given data, No of bolts = 10 Diameter of bolt (d) = 16 mm Diameter of bolt circle = 0.650 m…

Q: < 250 mm A D P = 25 kN B 30 60 C TOP VIEW 280 mm Member AD is fabricated by joining two bars…

A: E=2G(1+μ)μ=E2G-1 GIVEN E=205GPa G=82GPa NOW USING ABOVE FORMULA μ=2052x82-1 μ=.25

Q: For the connection shown, the bolt diameter is d = 15 mm. The average shear stress in the bolts…

Q: G K H

A: Given data:

Q: Solve the plate shown in the figure, Include fbd on solutions

Q: D Front view 18 mm 6 mm B IB Side view 160 mm 120 mm Top view In the steel structure shown, a…

Q: D CED Front view 18 mm 6 mm B B Side view 160 mm 120 mm A Top view In the steel structure shown, a…

Q: 4.1 The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD…

Q: A force P = 85 kN is applied at the plate-bolt connection shown. Determine the required diameter in…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: The safety stress for the steel bar shown in the figure is ϭallow= 160MPa. According to the…

A: Solution:

Q: The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed…

Q: LBC LAB

Q: The assembly consists of two steel bolts AB and EF and an aluminum rod CD. When the temperature is…

A: Free body diagram of rigid cap. Applying equation of equilibrium in vertical direction,Summation of…

Q: The safety stress for the steel bar shown in the figure is σallow= 160MPa. According to the greatest…

A: Solution:

Q: III. By any method, solve the axial bar forces of the truss shown, and identify whet compression or…

Q: Problem 3 The shaft consisting of steel and aluminum segments carries the torque T and 2T. Find the…

Q: The Howe truss is subjected to the loading shown. Determine the force in member GH in kN. Use…

A: To find force in member GH

Q: "Determine thé forcés in all the members, and state if these meņmbers are in tension or compression.…

Q: Cm 4m 4m Gom G Gm. F Gm 76 KN 14 76 KN

Q: solve the stresses in members DF,DG and EG using method of sections

A: Given data Using method of section

Q: Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P =…

Q: A rigid bar BCD is connected by link at AC at point C as shown in the figure. The Structure is…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

The compound shaft, which is fixed at both ends, is composed of Aluminum shaft ABC (Gal = 24 GPa, d =
50 mm), steel sleeve AB (Gst = 76 GPa, dout = 90 mm), and copper sleeve ABC (Gcu = 45 GPa, dout = 75 mm),
which are all welded together. Considering the allowable shear stresses (Tal, Ist, Tcu), determine the
maximum allowable torque T (kN-m) that may be applied at B as shown.
Note: Double-headed arrows follow the direction of the thumb when using the right-hand rule.
A
Parameters
Tal = 51 MPa
Tst = 101 MPa
Tcu = 71 MPa
steel
Cu
AI
L = 5m
B
➡T
Cu
AI
L= 3.5m
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft in MPa. ( COMPLETE SOLUTION NO ROUNDING OFF)
Compute the total deformation (in mm) of the tapered square steel bar caused by the 30-kN axial load. Use E = 200 MPa. 20 mm 30 mm 30 kN 30 kN 400 mm
A flanged bolt coupling consists of six - ½ inch steel bolts evenly spaced around a bolt circle of 12 inch in diameter, and four – ¾ inch aluminum bolts on a concentric bolt circle 8 inches in diameter. With an applied torque of 260 kips*inch. determine the max shearing stress in the aluminum and steel bolt. Use Gst = 12x10 6 psi and Gal = 4x106 psi
IDENTIFY THE ZFM ZERO FORCE MEMBERS
0.16
Read the question carefully and give me right solution with clear calculations
Q-1 Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa.c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4.
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
I Review Part A The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.035 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. µA T = 3.7216 Units Figure Pearson
Q.1//The bar AD is considered to be absolutely rigid and is horizontal before the load of 200 KN is applied. The connection at A is a pin, and AB is supported on the steel rod BE and the copper rod CF. The length of BE & CF is 250 mm. The cross sectional area of CF is 400 mm, the area of BE is 200 mm. тт. Determine the stress in each of the vertical rods. The weights of all bars are negligible. For copper E=120 GPa, for steel E=200 GPa. 200 KN A• D 1.5 m 500 mm 1500 mm 250 mm steel copper
Part (b) (A hollow circular steel drive shaft has an outer radius of R mm and an inner radius of r mm as shown in Figure Q9-b. Figure Q9-b: Given that r-16, R-30 and the maximum allowable shear stress in the shaft is 75 N/mm2, calculate the maximum permitted torsional moment, T., that can be transmitted by the shaft. T: [(b)
13