The collar of mass m (given below) is moving along the smooth guide shown. Its velocity is 2 m/s upward at D. The ABC part of the guide is a semi-circle with a radius of 0.2 m. The spring has an unstretched length of 0.2 m and a stiffness k (given below). a) If the motion is in a vertical plane, determine the speed of the collar when it is at B.

The collar of mass m (given below) is moving along the smooth guide shown. Its velocity is 2 m/s upward at D. The ABC part of the guide is a semi-circle with a radius of 0.2 m. The spring has an unstretched length of 0.2 m and a stiffness k (given below). a) If the motion is in a vertical plane, determine the speed of the collar when it is at B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular beam is supported at both ends. It carries two concentrated load of 190KN, a clockwise moment of 160KN- m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 150GPA. Solve the following if the reaction at point B is 309.63888888889KN, upward. USE ANY МЕТНOD BEAM DIMENSION: Width = 130mm , %3D Height = 460mm %3D NOTE: b = 4.2m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P W M 1m 1m 1m Determine the deflection at midspan
A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T1" developed at left fixed support at a is ___KN-m A 3.82 B 1.18 2.64 0.48 5.03 E
The 10.5-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 N. m. The spring is unstretched when 0 = 0, and has a stiffness of k = 60 N/m. (Figure 1) Figure k = 60 N/m -0.5 m B 2 m 50 N m < 1 of 1 Part A Determine the smallest angle for equilibrium. Express your answer in degrees to three significant figures. 0= Submit ΫΠΙ ΑΣΦ Provide Feedback Request Answer vec 3 ?
A rectangular beam is supported at both ends. It carries two concentrated load of 30kN, a clockwise moment of 150KN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 130GPA. Solve the following if the reaction at point B is 256.73846153846KN, upward. BEAM DIMENSION: Width = 130mm, Height = 360mm NOTE: b = 4.8m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) w What is the numeric value of C1 (1st Constant)? kN-m2 Determine the deflection at midspan.
A load Pis supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 12200 ksi] rods, and a solid steel [E = 31000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.72 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assune Ly=59 in and L2=89 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 16 kips is applied. (2) (1) L2 (1) |L1 O B C Answers: i ksi. i ksi.
The 10-kg uniform rod is pinned at end A. If it is also subjected to a couple moment of 50 N ⋅ m, determine the smallest angle θ for equilibrium. The spring is unstretched when θ = 0, and has a stiffness of k = 60 N/m.
2. The uniform slender bar of length 2.05r and mass m rests against the circular surface as shown. Determine the normal force at the small roller A and the magnitude of the ideal pivot reaction at O. A m 1.45 r 2.05 r
The beam supports a uniform load of 3.0 k/ft and a concentrated load of 12 k as shown in the figure below. Assume D is a pin support and B is a roller. Determine the reactions at B and D. Write the equation for the bending moment in beam segment BC. Assume "x" is measured from point B. • Write the equation for the shear in beam segment CD. Assume “x;" is measured from point D. 112 k 3.0 k/ft A C 12 ft 12 ft
for the beam shown in the figure, a) find the equation of elastic curve by integration method. b-) Draw (Ty), (mx) oliagrams of the beam. c-) find the Suppert reactions. 29=260 9=130 9-130 E L-158cm Figure: L=158 cm
From the beam and loadings shown. a. Compute the maximum moment of the beam. b. Compute the location of the point where bending moment goes from positive to negative (point of contra flexure) from A. c. Compute the maximum normal stress due to bending. Use INA = Ig + Ad² for moment of inertia. 30 mm 100 kN/m 75 mm 56 mm 1.5 m 1.0 m
4. A planar truss that is supported by a rolling pin support at point I and a fixed pin support at point A is shown in the accompanying figure. Two point loads are applied on the truss at points D and F, as indicated in the figure. Assume that all members of the truss are massless. n₂ 400m 40 FARN an AKN m 300 300 (a) Draw a free body diagram of the entire truss. (b) Using equilibrium conditions, calculate the reaction forces at points A and I. (c) Draw a free body diagram of point H; calculate the axial forces acting on member HH. (d) Determine the axial forces in members DF, DG, and EG.
%3D If the intensity of the distributed load acting on the beam is w = 3KN/m, determine the reactions at the roller A and pin B. 3 TA