the capacitive reactance value is and the When the frequency is inductive reactance value is a) increased / increased / increased b) none of the options c) decreased / decreased/increased d) decreased /increased / decreased O e) increased/ decreased/ increased

Q: A transformer with 120 primary turns and 10 secondary turns is connected to a 240V AC supply and…

A: We need to find current voltage and power for given circuit

Q: Refer to the given circuit below. Determine the potential at node c if the reference is node b. R1…

A:

Q: a. Which of the following is a vector quantity? A. Voltage B. Current С. Area D. Volume b. Absolute…

A: a. Current is a vector quantity as current is defined by both direction and magnitude. Thus the…

Q: Complete the timing diagram for the circuit until the arrow: CLK

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Perform binary addition: 1111 with 1010 which yields O a. 10100 O b. 11001 O c. 01101 O d. 10010

A: Given, To perform binary addition of 1111 with 1010

Q: A 3-phase, 400 V, 6-pole, 3-phase, 50 Hz, star-connected synchronous motor has a resistance of 0.5 N…

A: Given Data: Ra = 0.5 ohm/phase Xs = 4 ohm/phase V = 400 V P = 6

Q: and the When the frequency is inductive reactance value is , the capacitive reactance value is O a)…

A: The value of the capacitive reactance and the inductive reactance are changes with the frequency .

Q: The switch in the circuit shown in the figure is its initial position for a very long time before it…

A: We need to analyse the given circuit

Q: What is an active load circuit for amplifier? What is a driver circuit? What makes this unbalanced?

A: 1)Active load: The transistors M5 and M6 forms an active load. They force the current to pump from…

Q: In a balanced three-phase, 208 V circuit, the line curren

A: Active Power- It is power utilized by the load. It is denoted by P Reactive power- It is the power…

Q: Ql: A) A 30, 3 wires T.L system work by 380 KV between lines to supply a load with lagging power…

A: Since you have asked multiple questions in a single request, we will be answering only the 1st…

Q: mechanical power output

A: Three Phase Induction machine- This Induction machine comprises of rotor and stator as it basic…

Q: Three sinusoidal alternating currents of RMS 5, 7.5, and 10 A are having the same frequency of 50 Hz…

A: given three sinusoidal alternating currents of RMS values 5 A, 7.5 A, 10 A are having the same…

Q: A three phase power system has a fault level of 500 MVA and Sg = 100 MVA at a 132 kV busbar. What is…

A: Given, A three phase power system has SB=100 MVAVB=132 kV Fault level is 500 MVA.

Q: Hiwo: Fird the B function, freguerey of oscillation ard E for oscilletion for the cirenit shown…

A:

Q: Find the current I, in this circuit. 3/0° A -j20

A: Here shown a parallel circuit current find by current

Q: R1 R2 R3 R4 E1 E2 30 30 30 20 11 V 10 V 4 A a b R2 R1 R3 E2 E

A:

Q: Analyze the circuit to determine the voltage at + 5V all nodes and the currents through all…

A:

Q: Determine the Current Density for the following transformer winding (Fill Factor = acceptable? 0.92)…

A:

Q: -j 200 b 1 k a E 3k 10 k 8 k .004 Va

A:

Q: 4.9 Find V, in the network in Fig. P4.9 using superpositon. + V, - o 3 kn 8 kN 12 V 6 kl 2 mA 2 kn…

A:

Q: b) A sinusoidal voltage is applied to the resistive circuit in Figure Q.3.b. Determine I R 10V 1.0…

A: Given: The circuit is,

Q: Calculate the electrical displacement between adjacent slots of a 16-pole alternator with 144…

A: Electrical displacement between adjacent slots given as Beta=(180* poles)/slots

Q: The closed loop gain (C/R) of the system shown below is: R Оа. -2 O b. 2 О с. -6 O d. 6

A:

Q: Identify each characteristic curve by the type of FET that it represents. Ip -VGS +VGs

A: For N channel JFET, the VGS voltage is negative and the saturation current IDs we obtain at Vgs.

Q: A balanced three phase load of 10 MVA , 80 percent pf and 33 kV is connected at the end a TL whose…

A: For Regulation calculation, First, find the Sending end voltage using receiving end voltage and Load…

Q: Given the closed loop system, what is the forward transfer function? R K (1+ K)e + 1 0.1 а. 0.1 O b.…

A: We need to find out forward path Function and transfer function

Q: Find and sketch the unit step response s(1) for i(t) in the circuit below. What is the time…

A: In this question we need to find and sketch current i(t)

Q: If the line frequency is 50 Hz, the output frequency of a bridge rectifier is

A:

Q: a. The permeability of a material means A. strength of permanent magnet B. strength of an…

A: We need to select correct option for given statement

Q: a. Semiconductor intrinsic carrier concentration increases with temperature. b. At the same room…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: Find the transfer function G(s) = V:(s) for the electronic circuit shown. (s)'A 110 k n 600 kQ 4 μF…

A:

Q: Reduced the given block diagram in canonical form and then find the transfer function. 1/s? R + 35…

A: Reduce the following block diagram into canonical form then find the transfer function of the block…

Q: Q1)information signal is PCM using 8 levels quantization if the signal is given as cos(4T with…

A: Quantization level given is L=8 Encoding bit will be calculated as, L=2n So, 8=2n⇒n=3

Q: A generator at no-load operates 61 Hz, slope 1MW/Hz. Load 1= 1.0 MW and load 2=0.8MW are  connected.…

A: In this question we need to choose a correct option

Q: b) In your own words, define the "skin effect" in transmission lines and discuss how can it be…

A: Skin effect: The non uniform distribution of current through the conductor caused to non uniform…

Q: The Current flowing through a heating element is 6 A when a PD of 36 V is applied across it. Find…

A: Given, Current flowing through heating element, I=6 A Potential difference across it, V=36 V

Q: x(n) y(n) 7/12 -1/2 -1/12

A:

Q: Calculate the output voltages V, and V, in the circuit. 200 ka 20 ka V, = 0.2 V 200 ka 10 k2

A:

Q: VDD Rp2 RpI RD1 M2 HE Pout R1 Cp2 M1 Vin H CG |Rs2 +Cs2 R2 Rs1 Cs1 Vss = 0 V SS what makes this a…

A: There are two types of amplifier connection one is cascode and the other is the cascade. The cascade…

Q: %3D For the system given in Figure 1, where G(s) (s+4)(s-6) R(s) + E(s) C(s) G(s) lanA Figure 1 (la)…

A: Given the system as shown below: G(s)=K(s+1)(s+10)(s+4)(s-6) a) We need to sketch the root locus…

Q: Identify each characteristic curve by the type of FET that it represents. Ip -VGS

A: This question is related to MOSFET characteristics

Q: F25/A +0.372

A: In the following section the addition of F25/A and 0.372 have been performed.

Q: 2- For the circuit in procedure, apply the superposition theory to calculate theoretically the…

A: When more than one source is present in the electrical network, the Superposition theorem is used.…

Q: From the circuit in Figure 3, the voltage across the ideal diode is 1.5 kQ 10 V O 2.5 ko Figure 3 O…

A: Voltage across ideal diode is given as from figure diode is reverse bias because diode  cathode is…

Q: the capacitive reactance value is and the When the frequency is inductive reactance value is a)…

A: Capacitive reactance inversely proportional to frequency  Inductive reactance directly proportional…

Q: 10. Consider in Figure 6.43 the design of a T-network that transforms a 50 2 load impedance to 5 N:…

A: The circuit is as shown below,

Q: (1100 Full the following blank 0001 0111 0110)BCD (5321) +(1000 1010 0111)BCD7421=( )8 21402 121015…

A:

Q: 3. Determine Vo and sketch output waveform. Sketch v, for each network of Fig. 181 for the input…

A:

Q: Find the current I,

A:

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.