The cantilever beam is loaded with Pupward concentrated load acting at distance s from the free- end and the distributed load intensity is defined by the equation W = -7x + 63 in kN per meter is loaded from x = 0m (free end) to x = 9m (fixed end) as shown. The beam has the following properties: E = 200 GPa, I = 2x10⁹ mm W 5 m B 3 m с 2 fix A.) If the load P = 250 kN and s = 2.00 m., 1. What will be the shear at the fixed end? 2. What will be the moment at the fixed end? 3. What will be the complete equation for Ely" in kNm (use fractions for the coefficients)?

The cantilever beam is loaded with Pupward concentrated load acting at distance s from the free- end and the distributed load intensity is defined by the equation W = -7x + 63 in kN per meter is loaded from x = 0m (free end) to x = 9m (fixed end) as shown. The beam has the following properties: E = 200 GPa, I = 2x10⁹ mm W 5 m B 3 m с 2 fix A.) If the load P = 250 kN and s = 2.00 m., 1. What will be the shear at the fixed end? 2. What will be the moment at the fixed end? 3. What will be the complete equation for Ely" in kNm (use fractions for the coefficients)?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam AB of length L (Figure below) is freely supported at A and at a point C which is at a distance KL from the end B. If a uniformly distributed load of intensity w per unit length acts on AC, find the value of K which will cause the upward deflection of B to equal the downward deflection midway between A and C. A W B KL L Round your answer to 2.d.p Hint: Since there are no loads on the part CB of the beam and the implication in the question is that the beam is weightless, the length CB will remain straight but will rotate about C.
4 m 450 mm [s0 mn [50 mn 18 350 mm 50 mm Figure la Figure Ib Before a diver jumps into the water, helshe stands at point C, causing a deflection of the board A-B-C in the figure. The board A-B8-C has a modulus of elasticity of E = 15 MPa with the sketched dimensions and cross-section (fig. 1b). Assume g=10 mis?. Provide all steps of your working and solutions handwriten; include diagrams and coordinate systems. a. Determine the reactions at each support A and B. Use the variable w for the weight of the diver, include a free-body diagram.
A beam with length L is FIXED at both ends. It is loaded with a concentrated force P at L/3 from the first support. (a) Draw the Loading Diagram. (b) Determine the deflection at midspan, EI is constant. (c) If the beam is made of steel, what is its elastic modulus? (d) If the beam has a length of 10 meters, cross section of 200x200mm, and force P is 10 kN, what is the deflection at midspan (in millimeters)?
4. A copper bar 250 mm long and 50mmx50mm in cross-section is subjected to an axial pull in the direction of its length. If the increase in volume of the bar is 37.5 mm', find the magnitude of the pull. Take p-0.25 and E-100GPA. Answer: P-30 KN. 5. A steel bar 50mmx50mm in cross-section is 1.2 m long. It is subjected to an axial pull of 200 KN. What are the changes in length, width and volume of the bar, if the value of Poisson s ratio is 0.3 ? Take E as 200 GPa. Answer Al-0.48mm, Ab-0.006mm and AV-480 mm'. 6. A reetangular bar 500 mm long and 100mmx50mm in cross-section is subjected to forces as shown in figure. What is the change in the volume of the bar? Take modulus of elasticity for the bar material as 200 GPa and p-0.25. Answer :AV-137.5 mm'. 300 KN 100 KN 50 100 200 KN 500 mm
A simple beam AB supports two concentratedloads P at the positions shown in the figure. A support C at the midpoint of the beam is positioned at dis-tance d below the beam before the loads are applied. Assuming that d 5 10 mm, L 5 6 m, E 5 200 GPa, and 198 10 mm 6 4 I 5 3 , calculate the magni-tude of the loads P so that the beam just touches the support at C.
Rcmid=13392 O Codex Alimentarius... A What requirements. 国 Re ey to.. EHide ble This course Let's consider a fixed supported beam subjected to a triangular distributed load as shown in the figure below. The equation of the shear force (0 sxs 2m) is given by: 100 N/m 2 m Select one: O v(x) = -300 X2 +300 (N) O v(x) = -100 X² + 100 (N) O V(x) = -500 X2 +500 (N) O v(X) = -75 X2 +75 (N) O v(x) = -200 Xx² + 200 (N)
A 3mm thick hollow polystyrene cylinder (E = 3 GPa) and a rigid circular plate (only part of which is shown in Figure 2) are used to support a 6mm diameter steel rod AB (E = 200 GPa) of length 250mm against a rigid baseplate. If a 3.2 kN load P is applied at B, determine the following: - (a) the elongation of rod AB. (b) the deflection at point B. (c) the average normal stress in rod AB. 30 mm 250 mm A 6 mm P= 3.2 kN 50 mm Circular plate Polystyrene cylinder Baseplate
The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 20 mm² and is made from 6061-T6 aluminum. (Figure 1) Figure 1.5 m • 300 N/m -2 m 1 of 1 > Part A Determine the vertical deflection of the bar at D when the distributed load is applied. Express your answer to three significant figures and include the appropriate units. dp = Submit μÃ Value Provide Feedback Request Answer Units
The beam has a Young's modulus of Eo 100 GPa, a length of / = 4 m and 2nd moment of area of I₂ = 4 m². The intensity of the uniformly distributed load is w = 100 N/m. Now calculate the maximum beam deflection: Umax = X Expected answer: 0.1149623254 (m)
2 By using Conjugate BeamMethod, Detemine the deflection at the free end of the beamshown 180 kN 15 kN/m B D 5 m- El = constant E = 70 GPa 1 = 2,340 (106) mm* -5 m- -4 m-
A beam is subjected to a linearly distributed downward load and rests on two wide supports BC and DE, that exert uniformly distributed upward loads as shown. Determine the values of wec and WDE corresponding to equilibrium when WA = 750 N/m. 1200 N/m 20 C WBC ADA A 0.6 m- B' 0.8 m The value of WDE is The value of wBc is [ -3.1 ms -6 m- N/m. N/m. D (DE 1.0m E F
An 8-m simply supported beam AB carries a downward 8-kN point load located 6 m from the left support A. Determine the value of tB/A. Answer: __________/EI (numerical answer only in 3 decimal places, indicate sign, no sign means positive)