A 3mm thick hollow polystyrene cylinder (E = 3 GPa) and a rigid circular plate (only part of which is shown in Figure 2) are used to support a 6mm diameter steel rod AB (E = 200 GPa) of length 250mm against a rigid baseplate. If a 3.2 kN load P is applied at B, determine the following: (a) the elongation of rod AB. (b) the deflection at point B.

A 3mm thick hollow polystyrene cylinder (E = 3 GPa) and a rigid circular plate (only part of which is shown in Figure 2) are used to support a 6mm diameter steel rod AB (E = 200 GPa) of length 250mm against a rigid baseplate. If a 3.2 kN load P is applied at B, determine the following: (a) the elongation of rod AB. (b) the deflection at point B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂ bonded to an 80-mm-long hollow rubber cylinder with a modulus of rigidity G = 10.93 MPa. Determine the required value of the ratio R2/R1 if a force P = 13 kN is to cause a 2-mm deformation of rod A. B R₁ R₂ .. 80 mm The required value of the ratio R2/R₁ is 1.422
An E-Shape beam with the cross-section is bent about vertical axis. As shown in Figure Q3, N-N is plastic neutral axis Assume that the yield stress, oy is 275 MPa and the elastic bending moment, My is 18.88 kNm, (i) determine the plastic moment, M, of the beam. (ii) determine the value of the shape factor for the beam. N 20 тm | 20 тm 100 тm 20 тm 60 тm 20 тm 80 тm N Figure Q3
2.4 The truss shown is the same as in Example 2.1 except that the area of bar ab is a variable. E = 200,000 MPa. (a) For what value of Aah is v. = 0? Is this a function of the magnitude of the applied load? (b) Is it possible to obtain zero u, by varying A? (c) Suppose the applied load were vertical rather than horizontal, would it then be possible to obtain zero u, by varying Aab? If so, for what value of Aab? What would be the corresponding v.? 500 kN Fah = +400.6 kN Aab 4 m 6 m 3 m Problem 2.4 Fac = -277.8 kN Aae = 8000 mm?
The cantilever T- beam is loaded as shown in the figure. Ti 80 mm 40 kN/m NA --- 120 mm 2.0 m INA = 30x105 mm What is the value of fleure stress in a distance 1.20 m from the free end at the topmost fiber of the beam section?
QUESTION 3. A simply supported beam, having notches on its surface, is subjected to a triangular distributed load as shoen in the figure. The factor of safety is defined to be 1.5 for yielding. Calculate the maximum value of wo that the beam can support. The notch radius is 10 mm. 10 mm Wo 50 mm 40 mm Losmtosm- 0.5 m -0.5 m -0.5 m
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in Fig. 2-42. Through a fabrication error, the central bar, ②2, is 0.0005L too short. All bars are of identical cross section and of steel having E = 210 GPa. Find the stress in each bar after the system has mechanically been pulled together so that the gap A is closed. Ans σ-35 MPa σ = 70 MPa Fig. 2-42
1. A polyethylene bar (E = 1.4 GPa and v = 0.4) having di = 70 mm is placed inside a rigid steel tube having an inner diameter d2 = 70.2 mm. The polyethylene bar is then compressed by an axial load P. (a) At what value of P will the space between the polyethylene bar and the steel tube be closed? (b) If the compressive force P = 50 kN, determine the normal stress on the cylindrical surface of the bar, axial strain and the change in volume in the bar. Steel tube. 7p Ip Polyethylene- bar
A high-strength bolt that passes through a steel plate is subjected to a tension force of P as shown in the figure. The hole in the metal plate has a diameter of D=17 mm which is slightly larger than the diameter of the bolt (d, = 12 mm) to allow for easy installation process. The plate has a thickness of t= 9 mm. The bolt head has a thickness of a = 9 mm and an outer diameter of dn = 24 mm. %3D Determine: A) the maximum value of P before the shear stress in the rod head exceeds Thot = 105 MPa. B) the maximum value of P before the punching shear stress in the support plate exceeds Tplate = 75 MPa. C) the maximum value of P before the bearing stress between the rod head and the support plate exceeds aplate = 110 %3D MPa. D) the maximum value of Pmax that can be supported by the structure.
Q1. An aluminum rod is rigidly attached between a steel rod bronze rod as shown in figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will n exceed a stress in steel of 90 MPa, in aluminum of 140 MPa bronze of 120 MPa. Aluminum Вronze A= 300 Steel A=100 A=200 ЗР 2P 5P 2.5m 2.0 m 1.5 m
EXAMPLE 4.4 Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. Knowing that the magnitude of P is 4 kN, determine (a) the value of Q so that the deflection at A is zero, (b) the cor- responding deflection of B. 20-mm diameter 0.4 m 0.5 m 60-mm diameter
The three equally spaced vertical rods in Fig. (a) are securely attached to a rigid horizontal bar. The two outer rods are made of an aluminum alloy, and the middle rod is steel. The cross- sectional areas of the rods are shown in the figure. Determine the residual stresses in the rods after the load P has been increased from zero to the limit load and then removed. The material properties are E = 70 GPa, Oyp = 330 M Pafor aluminum, and E = 200 GPa, Typ 290 MPa for steel. Neglect the weight of the bar. Aluminum 600 mm² Steel (a) շատ (06 Aluminum 600 mm² 250 mm 100 mm