The cantilever beam is loaded as shown in the figure. Derive the equations for the shear force (V) and the bending moment (M) for any location in the beam. Analyze the beam from the left, taking point A as the origin. 4 kips/ft What is the moment (in kips-ft) at x = 4.00 ft? What is the shear force (in kips) at x = 5.50 ft? What is the moment (in kips-fi) at x = 13.00 ft? What is the behavior of V equation between points B and C? What is the behavior of M-diagram between points B and C?

The cantilever beam is loaded as shown in the figure. Derive the equations for the shear force (V) and the bending moment (M) for any location in the beam. Analyze the beam from the left, taking point A as the origin. 4 kips/ft What is the moment (in kips-ft) at x = 4.00 ft? What is the shear force (in kips) at x = 5.50 ft? What is the moment (in kips-fi) at x = 13.00 ft? What is the behavior of V equation between points B and C? What is the behavior of M-diagram between points B and C?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

143 in Newton 30 40° T15° Compute for the forces on the following based on the above figure: a. F along a is [forceA] b. along b is [forceB]
PROBLEMThe beam shown below has internal hinges at points B and D. Assume EI is constant. Using your most convenient methodshow the following:a. Magnitude and directions of the support reactions (Ax,Ay, MA, Cy, Fy). b. The elastic curve.c. Vertical displacement at B. d. Rotation just to the left of B. e. Rotation just to the right of B.
1. Determine the Moment due to force F about: a. Point O b. Point B Note: The thickness of the beam is NOT negligible and is given in the image. Y ///// F=225N 9m 3m Th 5m B 2m O
The continuous beam is loaded as shown in the figure. The supports at A is pin, B, C, and D are rollers. If there has a support settlement of 18 mm at B, 33 mm at C and 16 mm at D. Use Slope- Deflection in determining the following: a. Reaction at the given supports. b. Shear and moment diagram of the beam E = 210 GPa and l=1350x106 mm4 88 KN 3.6 m 91 kN 74 kN/m 60 KN 40 kN/m D 5m A B 56 kN-m 1.5m 1.5m 1.1 C 2.4m 1.4m 7.3 m 7
The continuous beam is loaded as shown in the figure. The supportsatA is fixed, B, D and C are rollers. Use Slope-Deflection in determining the following: a.Reaction at the given supports. b.Shear and moment diagramof the beam E =200 GPa and I=100x10^6 mm^4
Determine the moment at B for the beams shown using the three-moment equation. Express your answer in kip-ft and use two decimal places. 40 k 2.5 k/ft B D +128+12 - 24 ft - -24 ft - -21 – E = constant
The beam shown n the umage below ies on the ground e supporss the load Shown. Assuming the upward reaction of the ground is uniformy di sterbed,then: •wnat are the equations for the shear & bending-moment Curves. • what is the maxmum absolute value of the bending moment. CLx-x") wo wこ 3
a. Calculate reactive forces. b. Plot Shear & Moment Diagrams labeled with pertinent values. c. Calculate centroid of cross-section. 1 in.. d. Calculate Moment of Inertia of cross-section e. Calculate the maximum positive bending stress. f. Calculate the maximum negative bending stress. g. Calculate the maximum shear stress. 25 kips 25 kips 25 kips с D A It 1 ft 2 ft 6 ft E 2 ft B 4 in. 2 in. + a b 1 in.. 1 in. |←4 in.→|
24KN/m 12KN/m Зт A simply supported beam is loaded as shown in the figure. Assume El is constant. Determine: a. The reaction at the roller support in kN. b. The deflection at point "B" in terms of El. The deflection at the midspan in terms of El. C.
A beam is subjected to concentrated force as shown in the figure below. The EI of the entire beam section is constant. Try to draw the Shear Curve and Moment Curve of the beam.
Use CONJUGATE BEAM METHOD ONLY! E = 80 GPa & I = 1200x106 mm4 A. Find the Vertical Reaction at D in kN B. Find the Deflection at C in mm. C. Find the Slope of the elastic curve at D in Degrees Three Decimal places
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media