The bronze shaft is formed by attaching a hollow shaft to a solid shaft. The allowable shear stress of bronze is 100 MPa. Use G = 35 GPa for bronze. a. If the torque applied is 15 kN m, determine the maximum shearing stress developed in the bronze shaft b. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 100 MPa or an angle of twist of 3.5 in the 3.5-m length

The bronze shaft is formed by attaching a hollow shaft to a solid shaft. The allowable shear stress of bronze is 100 MPa. Use G = 35 GPa for bronze. a. If the torque applied is 15 kN m, determine the maximum shearing stress developed in the bronze shaft b. Determine the maximum torque T that can be applied to the ends of the shaft without exceeding a shear stress of 100 MPa or an angle of twist of 3.5 in the 3.5-m length

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m
A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0625-in. to new position Q' as shown in the figure. Determine the shear strain at Q'associated with the two edges (PQ and QR). Assume a = 4 in., b = 1 in., c = 2 in., and A = 0.0625 in. a R A Q' Answer:Y = i prad
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
The rigid bar ABCD of negligible weight is initially horizontal, and thesteel rods attached at A and C are stress-free. The 20-kip load is thenapplied and the temperature of the steel rods is changed by ΔT. Find ΔTfor which the stresses in the two steel rods will be equal. Use α=6.5x10-6/oF and E=29x106
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
thanks
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. 4 m a -1 m 100 KN 250 mm 1 600 mm 200 mm Section a-a
The stresses acting on an element are dx = 745 psi, ay = 615 psi, and Txy = 430 psi. (Consider only the in-plane stresses the stresses in the x-y-plane). Oy Determine the principal stresses (in psi) and angle of the principle planes (in degrees counterclockwise from the +x-axis). (For normal stresses, use the deformation sign convention. For maximum shear stress, enter the magnitude.) %1 = psi 0₂ = psi psi max = 8p = Show the stresses on a sketch of a properly oriented element. (Submit a file with a maximum size of 1 MB. Your submission will be graded by your instructor after the due date based on its accuracy. Your grade may change.) Choose File No file chosen This answer has not been graded yet.
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…