The BREAK command: a. Will work on lines and arcs b. Will work on closed objects c. Can have the same first and second break point d. All of the above

Q: Drawing an arc using the polyline command will spawn the same possibilities as employing the arc…

A: Drawing an arc using the polyline commmand will spawn the same possibilities as employing the arc…

Q: A pick and Place machine is being used to transfer a box. The arm is extended (out) by energizing a…

A: Solution:

Q: A symbol used to identify a physical feature of a part as a datum feature is called a: O Reference…

A: Reference feature: There are the feature where the other features are referenced from. feature…

Q: The needle-nose pliers shown in Figure A5 are used to either cut objects at location A or grip…

A: Given, Force = F

Q: SS? 2 (k+z)

A: see handwritten solution

Q: Briefly describe what is meant by a right handed system of coordinate

A: System of cordinates -  A cordinate system is defined as a system which is used to define the…

Q: Draw the schematic diagram for each of the following Boolean Expressions: 1. AB = X 2. A + B = X 3.…

A:

Q: Q4/ Using three different ways, compute the the moment of the force 400 N about O? 400 N 100 mm 60°…

A: Bending Moment(BM):- Bending happens whenever a point in time or couple acts about just a…

Q: Convert the octal number 23228 to its hexadecimal number equivalent, (base-8 to base-16).

A: Steps of Conversion: The simplest way is to convert the octal number into a decimal, then the…

Q: Transformations enable to manipulate the shape, size and position of model. true O false

A: To consider whether the given statement is TRUE or FALSE.

Q: -B E D

A: Kinematic diagram:

Q: What is the period in seconds?

A: To determine: The time period for the swing, where it takes approximately 2 seconds to reach on side…

Q: The hand writing is not very clear :(

A: Basically the miller indices are the set of numbers which define the particular plane in the crystal…

Q: The state of an object varies over time, but at any particular points it is determined by:   Which…

A: The state of an object varies over time, then it must be dependent upon the state of the object…

Q: A func tion f is given. cos x f(x) = Notice that f(x) is not defined when x = 0. What happens as x…

A: Given Data: The given function is f(x) = (1-cosx)/ At x = 0 the function takes the 0/0 form which…

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: For (x= 100, x>= 1, x++) cout <<x endl;

A: Given Code To find Output

Q: OFFSET command use to draw object parallel to selected object by determine radius distance point…

A: Computer-aided drawing is the way to draw the various views of the component. In the orthogonal…

Q: The motion shown by the arrow in the figure represents: Feed Motion Depth Motion Cutting Motion…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer a single…

Q: When two links of a mechanism become collinear (forming a straight line), the links are said to be…

A: A link is defined as a member of a mechanism that connects with other members of mechansim and…

Q: Write and draw the following grashof's criterion and kind of grashof's four-bar mechanism such as;…

A:

Q: All manipulators don't have workspace-boundary singularities. O True O False

A: Boundary Singularities (too known as workspace singularities) are a common sort of peculiarity.…

Q: please very urgent with count the number on the graph only

A: Here we can use Kutzbach's Criterion for determining degree of freedom.DOF=3(L-1)-2j1-j2here…

Q: Which of the following settings does not allow you to control point specifications?a. Grid b. Snap…

A: From the given options, the snap, ortho and the polar settings are used to specify a point. Hence…

Q: 1. Sketch the CAVALIER OBLIQUE of the given object. Use corner "A" for orientation.

A: according to the details provided in the question, we need to draw a cavalier view of the given…

Q: . Convert the decimal number 35710 into its binary number equivalent.

A: Given: A decimal number is, (357)10 .

Q: step of construction with sutible dimmenstion

A: To show the step of construction with sutible dimmenstion

Q: what type of CNC programming command sets the machine into a certain mode, which stays active beyond…

A: there are two type of CNC  command sets, 1).Modal:-in this set of command vommand are effective…

Q: What does the green axis represents? О хаxis O Y-axis O z-axis

A: In AutoCAD Fusion 360, the X,Y,Z axes are Represented by Red, Green, Blue respectively.

Q: QUESTION 4 A subset of the previous mode, VQC contains the stored codes for using the and tool…

A: Visual Quick Code is a template-driven conversational programming system that makes creating simple…

Q: Interchangeability system is also called

A: Solution:

Q: For a Quick-Return mechanism, define the following terms? a) Forward Stroke b) Return Stroke c)…

A: Quick Rerurn Mechanism is use in many machines like shaper machine, screw presses, mechanical…

Q: Which of the following statement is not correct for point function? elect one: O a. Point function…

A: Heat and work are path functions because it depends on the path followed during the process. For any…

Q: draw the Bode diagram

A: Given:

Q: In a single machine scheduling problem, all the jobs will have different sequences. true or false

A: In a single machine scheduling problem, different jobs are processed over a single machine. Since we…

Q: Describe the manipulator (joints, degrees of freedom, sketch the end effector workspace).

A: In the given figure there are three links in the mechanism, in which one link is a fix link and…

Q: What is relative position vector?

A: A vector is defined as a quantity that always has two properties - a magnitude and a direction and…

Q: True or False: You can only use the REDO command immediately after using the UNDO command.

A: The UNDO command takes back the work in a drawing session whereas the REDO command will take the…

Q: Apolyline can be broken into (aut cad) individual lines and arcs using which of the ?fowllowing…

A:

Q: Discussion object are the same? 2- When and why will the floating object become unstable?

A: This question is based on the topic of fluid mechanics in which it discusses about stability of…

Q: 3T tanux

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.