The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter 0.3 is filled with a liquid (SG>1, like glycerin) and the ret with water. The tank is now rotated about its vertical axis at constant angular speed w. Determine the value of

Name: The bottom quarter of a vertical cylindrical tank of total height 0.4
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The bottom quarter of a vertical cylindrical tank of total height 0.4 m and diameter 0.3 is filled with a liquid (SG>1, like glycerin) and the ret with water. The tank is now rotated about its vertical axis at constant angular speed w. Determine the

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.90P: The hemispherical glass bowl is filled with water. Find the location y of the center of gravity of...

See similar textbooks

Similar questions

4. The value of --- specifies whether the fluid can be assumed compressible or incompressible. 5. Archimedes' principle indicates - 6. A truck is filled with gasoline. If the container (tank) on the truck undergoes a then the liquid surface will begin to rotate clockwise about the center of the container and will eventually maintain a fixed tilted position.
A semicircular plate with radius r= 2 is submerged in water as seen in the picture. Using the facts that the density of water is 1000 kg/m³ and acceleration due to gravity is 9.8 m/s², calculate the fluid force (in N) against the side of the plate. Make sure your answer is correct to three decimal places at least. Fluid force radius-r N
A closed vertical cylindrical vessel, 1.80m in diameter, 3m high is 8/10 full of oil (SG=0.85) and revolved about its vertical axis with a constant angular speed. The air inside the vessel is 135 kPa. a. Determine the angular speed in radian per second necessary to set the vertex of the liquid surface 0.60m above the bottom of the vessel. b. What is the maximum pressure at the bottom of the tank during rotation? c. If the angular speed in rev/min is 128.71, determine the diameter of the portion free of liquid at the vessel in cm. d. If the angular speed is 200 rev/min, determine the area of the portion free of liquid at the bottom of the vessel.
The figure below shows a rectangular tank of dimensions ho = 2.5 m and b = 2 m is filled to the brim with a liquid of specific gravity 1.1 (tank is 1 m into plane of figure). The tank is subjected to a horizontal acceleration ax, and 30% of the liquid spills over. Determine the difference in liquid pressures at the lower left-hand corner (Point E) and lower right-hand corner of the tank (Point F). PE-PF= 1. [15.70090597, 16.672095597 Free surface ho Liquid X b Liquid at rest ➡ho kPa. 9 Free surface Liquid b ax Under constant acceleration
A vessel is filled with oil (ρoil = 900 kg/m3) up to 1 m of its height. It is 3m wide, 2m high and 10 m long.Find the following :A. The maximum horizontal acceleration that can be charged to the vessel without spilling anyoil.B. If this vessel is closed and is completely filled with oil and accelerated horizontally at a rate of 3 m /s2 .B.1. The total force acting at the rear wall and at the front wall of the vessel.B.2. The accelerating force on the fluid mass.
A semicircular plate with radius r = 2 is submerged in water as seen in the picture. Using the facts that the density of water is 1000 kg/m³ and acceleration due to gravity is 9.8 m/s2, calculate the fluid force (in N) against the side of the plate. Make sure your answer is correct to three decimal places at least. radius=r Fluid force = # N
Answer the following. A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to decrease by (0.08) percent. What is the bulk modulus of elasticity of the liquid? B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated about its central axis at (60 r.p.m). How much liquid is spill and how deep of the water at the central axis.
The three-legged manometer in Fig. is filled with water to a depth of 20 cm. All tubes are long and have equal small diameters. If the system spins at an angular velocity about the central tube, (a) derive a formula to find the change of height in the tubes; (b) find the height in cm in each tube if ω = 120 r/min.
The movement of the fluid element has three distinct features in space simultaneously, explain by figures.
2. Cylindirical cup below is open at its top and totally filled with water. It is rotated with a contant angular velocity = 36.5 rad/s. Calculate volume and depth of water retained in the cup after this rotation. Hint: Volume of paraboloid is equal to the half volume of a cylinder with the same height. 0.4 m 0 0.08 m M X @₂=0
What would be the velocity of liquid (m/s) at radius of 8 cm? The rotation occurs around axis A-A, during rotation, the liquid in the left leg (with a ?diameter of d) decreases a distance h1=1.4 m + 3d 10 cm: 25 cm
Which is the most accurate statement of Bernoulli's Principle? Select one: O a. Fast -moving air causes lower pressure O b. Lower pressure causes fast-moving air O c. Both A and B O d. None of these The body is stable if the center of gravity of the body is below the metacenter. Answer: The amount of energy per pound or Newton of fluid is called the head. Answer: For incompressible fluids, the flow rate is constant (write in small letters).