The bent bar as shown below is supported by a cable AE, a ball-and-sockejoint at O, and a journal (slider) bearing at D. At the journal bearing D, the momesupport reactions and the force support reaction along y-axis are zero. The 2-kipforce and the 6 kip-ft couple-moment are parallel to z-axis and applied at point EDetermine the tension in the cable AE and the support reactions at O and D.X4 ftMESTZ6 kip-ft2 ft B 2ft2 kips3 ftDe[ 1 kip = 1000 lb. 1.E1114 ftitT

Find outDetermine the tension in the cable AE.Given(I kip = 1000 lb)Load P = 2 kips = 2000 lbMoment…

The bent bar as shown below is supported by a cable AE, a ball-and-socke joint at O, and a journal (slider) bearing at D. At the journal bearing D, the mom support reactions and the force support reaction along y-axis are zero. The 2-ki force and the 6 kip-ft couple-moment are parallel to z-axis and applied at point Determine the tension in the cable AE and the support reactions at O and D. N E 14 ft

The bent bar as shown below is supported by a cable AE, a ball-and-socke joint at O, and a journal (slider) bearing at D. At the journal bearing D, the mom support reactions and the force support reaction along y-axis are zero. The 2-ki force and the 6 kip-ft couple-moment are parallel to z-axis and applied at point Determine the tension in the cable AE and the support reactions at O and D. N E 14 ft

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.42P: The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a...

See similar textbooks

Similar questions

The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A caused by the applied force P.
The 350-lb homogeneous plate has the shape of an isosceles triangle. The plate is supported by a thrust hinge at A, a slider hinge at B, and the cable CD. Find the force in the cable and the magnitudes of the hinge reactions.
5 kN -1.5 m- 45° Consider the three bars shown: ABD, BC and DCE. The 5 kN force acts only on bar ABD. Likewise, the 3 kNm couple moment also acts only on bar ABD. Pin D connects bars ABD and DCE, and bar BC is connected to bars ABD 1.5 m and DCE by pins at B and C, respectively. a. Obtain all support reactions at pin A, rocker at E, and the force along bar BC. The pin at B is subjected to single shear, and the pin at A is subjected to double shear. If the maximum allowable shear stress for the pin material is 50 MPa, determine the minimum 3 kNm Allowable diameter of pins A and B, respectively. Draw state of stress on volume elements taken from pins B and A, separately. 1.5 m d. If diameter of bar BC is 37.5 mm, determine the average normal stress along bar BC.
The rigid body is supported by a hinge at A and a cable at C. The hinge resists 5.5m translation in all three coordinate directions and rotation in the x and y directions. The 260 N force is in the -x direction and acts at the center of the 3m body. Find the tension in the cable and the components of the support C 2.5m 260N reactions at A. Your answer should include a properly Ilm annotated FBD. B 3.Im
A vertical force F of 176 N is applied to the bell crank at point A as shown in the figure below. A force P applied at B prevents rotation of the crank about point O. Determine the magnitude of the force P in N and determine the magnitude of the bearing reaction R at O in N.
A bent pipe is connected by a thrust bearing and a cable asshown. If a Force, F = 195 lb, is applied, what are the reactions at the thrust bearing and in the cable. The dimensions shown are a = 7.2 ft, b = 6.2 ft, and c = 4.6 ft.
Answer the following question: 3. Find the horizontal and vertical components of the forces at all joints. The reaction at point B is horizontal.
4. Find the all the support reactions and all the internal forces in all the members and whether in tension or compression. 5 kN 30°- A 6 m 1 m 2 m - y B 3 m 3 m
In the assembly shown, member AB is rigidly attached to the wall while an L bar is pinned to AB at E. Two forces P and Q are acting on the assembly shown. Force P lies on the x-axis while force Q is applied at point D along a plane parallel to the yz-plane . Which of the following best approximates the magnitude of the moment of force Q about the y-axis?
The L-shaped body is supported by a roller at B and a frictionless pin at A. The body supports a  vertical force FC at C and a  CCW couple-moment MD at D. Given, FC = 245.8 lb., and MD = 501 lb.ft. A) Determine the reactions at B , express in a cartesian vector.
The figure shows a schematic diagram of a torsion -bar suspension for an automobile( the torsion bar appears in cross section at A). If the three forces and the couple C= 27000 Nmm are equivalent to a upward vertical force R= 1200 N acting at D, determine H and V.
Statics, A hand-powered can crusher is shown in the figure. If a force of F is applied at C, find the magnitude of the vertical component of the force exerted on the can at D and the horizontal and vertical reactions at A.