The bell crack mechanism shown in Figure is in equilibrium for an applied load of F = 15KN at A and Fz at C. The pin at B has a diameter of 12mm. The thickness of the bell crank is 8mm while the support bracket has a thickness of 6mm. The bell crank and the support bracket each have an ultimate bearing strength of 550 MPa. a - 300 mm; b - 150 mm ; c 100 mm; 6 = 65° 30 (2) Bell crank a Fi 8 mm Bracket 6 mm 6 mm Connection detail Determine the factor of safety in the support bracket with respect to the ultimate bearing strength.

The bell crack mechanism shown in Figure is in equilibrium for an applied load of F = 15KN at A and Fz at C. The pin at B has a diameter of 12mm. The thickness of the bell crank is 8mm while the support bracket has a thickness of 6mm. The bell crank and the support bracket each have an ultimate bearing strength of 550 MPa. a - 300 mm; b - 150 mm ; c 100 mm; 6 = 65° 30 (2) Bell crank a Fi 8 mm Bracket 6 mm 6 mm Connection detail Determine the factor of safety in the support bracket with respect to the ultimate bearing strength.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
A cylindrical pressure vessel of 2.5m inside diameter, which is closed at both ends, having 12 mm wall thickness operates at 1.5 MPa internal pressure. The plates are welded on a 30° helical spiral as shown in the figure. Detemine the stresses Oayluld acting normal and tangential to the weld. Consider the element A drawn below. 30 da = 2.5mm t= 12mm p=1.5MPA
In the following structure, consider the following data: The connection at D is double and has a diameter of 50 mm. The beam BCDE has a thickness of 37.50 mm. The bar AB has a thickness of 37.50 mm and a width of 100. The connection at A is single and has a diameter of 67.50 mm. a. The normal stress in bar AB. Answ. 3.53 MPa b. The shear stress in the bolt at D. Answ. 6.25 MPa c. The shear stress in the bolt at A. Answ. 6.25 MPa d. The support stress between the beam and bolt D. Answ. 13.08 MPa
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.0 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.13 in., a length of L₂ = 28 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. y L₁ L2 TB. X (1) (2) N Answer: (a) TB = (b) T₁ = T₂= (c) DB = lb-ft lb-ft lb-ft rad B C
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.95 in., a length of L1 = 45 in., a shear modulus of 3800 ksi, and an allowable shear stress of 6.6 ksi. Brass segment (2) has an outside diameter of 0.80 in., a wall thickness of 0.14 in., a length of L2 = 32 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque TB that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.07 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.3 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
Reaction force Pin Retaining ring Ⓡ Force on link
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.90 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.6 ksi. Brass segment (2) has an outside diameter of 0.75 in., a wall thickness of 0.06 in., a length of L2 = 20 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.4 ksi. Determine: (a) the allowable torque Tg that can be applied to the compound shaft at flange B (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque T.
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.45 in., a wall thickness of 0.15 in., a length of L₂ = 30 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.2 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ L2 TB (1) Answer: (a) TB= (b) T₁ = T2= (c) OB= B lb-ft lb-ft lb-ft rad (2) C
Determine the maximum force P that can be applied to the specimen. The bar is made from steel and has an allowable stress of 150 MPa. 2R = 5mm R = 20mm- PP 150mm -6mm
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L₁ = 40 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.2 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.06 in., a length of L₂ = 24 in., a shear modulus of 6400 ksi, and an allowable shear stress of 7.7 ksi. Determine: (a) the allowable torque Te that can be applied to the compound shaft at flange B. (b) the magnitudes of the internal torques in segments (1) and (2). (c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB. L₁ (1) TB B L2 (2)