A plastic beam has a cross section with dimensions of a = 2.3 in., b = 8.1 in., d = 4.6 in., and t 0.6 in. The centroid is located c = 1.941 above the bottom surface of the beam, and the moment of inertia of the shape about the z centroidal axis is I, = 33.131 in. 4. For a shear force of V = 2650 lb, what is the maximum shear stress in the beam? y t (typ.) b. Answer:

A plastic beam has a cross section with dimensions of a = 2.3 in., b = 8.1 in., d = 4.6 in., and t 0.6 in. The centroid is located c = 1.941 above the bottom surface of the beam, and the moment of inertia of the shape about the z centroidal axis is I, = 33.131 in. 4. For a shear force of V = 2650 lb, what is the maximum shear stress in the beam? y t (typ.) b. Answer:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve the bending stress about the y-axis at points A and B. Indicate if the stress is in tension or compression. 200kN m B 200mm ▶44 15mm 200mm A 400mm 20mm
Help please!
The horizontal member shown in the figure is loaded by 57 kN at E. It is supported by steel connector AB (E = 200 GPa, A= 615 mm² ) and aluminum connector CD (E = 70 GPa, A = 525 mm² ). Determine the deformation incurred by connectors AB and CD. Also, calculate the vertical displacement of E. 57 kN 0.5 m 0.3 m E B 0.25 m 0.5 m
where, bf1= 260 bf2 = 120 tf = 25 tw = 16 d1 = 160 d2 = 110 1. Calculate the location of the neutral axis from the bottom of the beam in mm. 2. Compute for the moment of inertia in 1x10^6 mm^4. 3. What is the value of in kN/m, considering flexural stress in tension? 4. What is the value of in kN/m, considering flexural stress in compression? 5. What is the statical moment of area (Q) in 1x10^3 mm^3 ? Use three decimal places. 6. What is the value of in kN/m, considering shear stress at the welded section? 7. What is the safest value of in kN/m? Use three decimal places.
SHOW SOLUTION AND ILLUSTRATION
A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to a pure torque of T = 1120 N-m. The shear modulus of the steel is G = 80 GPa. Determine the magnitude of the angle of twist in a 2.0-m length of shaft. O 0.0145 rad 0.0280 rad 0.0207 rad O 0.0192 rad O 0.0241 rad
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
Question 5) The horizantal cantilever rigid beam AB has no mass and it is supported by an elastic rod at point C. The modulus of elasticity of the BC rod is E=200 GPa with cross-sectional area of 4=200 mm'. Calculate the magnitude of the distributed load q acting on the system so that the BC rod can be elongated by 2 mm. FEA 3m rigid B A 2m 1.5m
Part of a two story building is shown in the figure in which a concerte column and a steel column are used in the first and second floor. The compressive force on the roof of the second floor is PC = 400 kN. The compressive force on the first floor is PB = 310 kN. The steel [Esteel = 200 GPa] column is a wide angle steel shape that has a cross section area of A2 = 1850 mm2. The concrete [Econcrete = 30 GPa] column has a circular section with a diameter of d = 530 mm.[L1 = 4.8 m, L2 = 5.8 m] What is the displacement of the column at B?in mm What is the displacement of the column at C? In mm
X= 460 lb. Find the stress at points A and B. Determine the point where the neutral axis intersects like ABD. The neutral axis intersects AB at (blank) inches from A and intersects BD at (blank) inches from D.