The beam shown is constructed by joining two pieces of wood together using screws. If the resistant shear force of each bolt is Ft , determine the maximum allowable spacing s between the bolts. "cte" means constant "ambas piezas" means both pieces "sección trasversal" means cross section.

The beam shown is constructed by joining two pieces of wood together using screws. If the resistant shear force of each bolt is Ft , determine the maximum allowable spacing s between the bolts. "cte" means constant "ambas piezas" means both pieces "sección trasversal" means cross section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

Q: Compute its design strength based on rupture in kiloNewtons..* 412 485 453 389 438 This is a…

A: Given, Fu = 400 MPa Fy = 248 MPa D = 16 mm Dh = D + 2

Q: Two blocks of wood are joined together by a rectangular shear key with dimension bx d in mm. If P =…

A: Answer Let us first draw the free body diagram as shown below V is the shear force acting at the…

Q: A W18 x 86 beam is riveted to a W24 x 117 girder by a connection as shown. The diameter of the…

A: the method of steel design working stress method limit state of design ultimate load of design…

Q: 2. A connection is made from two 1.9 cm bolts in parallel, placed on a 21.6 cm wide steel bar. The…

A: Given data:- Diameter of bolts,d = 1.9 cm Thickness of steel bar, t = 2.54 cm Ultimate strength of…

Q: A steel plate (called cover plate) having cross-sectional dimensions 7.0 in. x 0.49 in. is welded…

Q: The plate shown is fastened to the fixed member by five 10-mm-diameter rivets. Compute the value of…

Q: Q1: For the simply supported beam of the cross sectional dimensions and load shown in the figure,…

Q: 5/8 in- diameter steel rod AB is fitted to a round hole near end C of the wooden member CD. For the…

A: This question is related to the Bending Stresses from Strength of Material. In this question we…

Q: A 3 x 8 member in a diaphragm resists a tension force of 20 k caused by the lat- eral wind pressure.…

A: Given:- The dimension of the member = 3×8 A tension force caused by the lateral wind pressure = 20 k…

Q: Apply AISC LRFD procedure to design a welded connection for a vertical truss member L127x76x9.5 with…

Q: The wood members A and B are to be joined by plywood splice plates that will be fully glued on the…

Q: Q2. The joint connection shown in Figure Q2 is subjected to a medium term tensile load under service…

A: The joint connection shown in Figure Q2 is subjected to a medium term tensile load under service…

Q: A 22.2 mm diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten…

A: db = 22.2 mmd = 18.6 mm = 34 kPa

Q: Problem 12-Method of Sections 2m 2m 10 11 12 13 10

Q: A singly reinforced rectangular beam 270 mm x 430 is reinforced with 4-16-mm-dia. rebars with yield…

Q: Part 2: Identify the read forces 4m 1) 60⁰ 4m 4m 10KN Rea'd: All member forces (use metheel of…

A: Given data Find all member force using method of joint.

Q: The beam shown is made from two boards. Determine the maximum load (w) that can be applied if the…

A: Solution:-

Q: 174069&message_id%3Dmid.%24CAAAA Question 3 For the truss shown, determine the forces in members (a)…

Q: Consider the truss shown. Determine the force acting on member CF, EF, and FG. B A D 3 m E 4 m 45 kN…

Q: 63.5 mm 6 @ 50 mm 63.5 mm 1. Determine the nominal strength for tensile yielding in the gross…

Q: Problem 3: Six 7/8-in-diameter rivets fasten the plate to the fixed member. Determine the average…

Q: In a truss girder of a bridge, a diagonal consists of mild steel flat 400 I.S.F. and carries a pull…

A: Truss girder A girder truss spans a roof or other structure and is designed to carry a greater load…

Q: The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm…

Q: A 12.5 mm x 150 mm plate is connected to a gusset plate having a thickness of 9.5 mm. Diameter of…

A: Given: 12.5 mm X 150mm plate thickness, t = 9.5 mm Dia of bolt = 23 mm Fy = 219 MPa Fu = 311.9 MPa

Q: An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt…

Q: What is the required diameter of sag rods in mm? Considering sag rods and tie rods at midspan…

Q: Determine the force in each member of the truss shown. Indicate whether the members are in tension…

Q: Two wood boards, each 20 mm thick, are joined by the glued finger joint shown. The finger joint will…

Q: The average normal stresses developed in section a - a of the turnbuckle, and the bolts shanks at B…

A: Given Data Cross sectional area at section a-a = 1in. × 0.25 in. Diameter of bolt shank (d) = 0.5…

Q: For the truss shown below identify zero force members. Make sure to state which joint you are…

Q: 2. Determine the force in members EF, EP, and LK of the Baltimore Bridge Truss, indicate if the…

Q: A 150 mm x 90 mm x 12 mm angular section is welded to a gusset plate as shown. Area of the angle is…

A: Area of the angle = 2736 sq.mmallowable shear= 150 MPaFt= 0.6FyFy= 250 MPa

Q: 4. Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using…

Q: The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

Q: Give the formula for the tensile and shear strength of the weld joint. Explain the various terms in…

A: Need to definethe formula for the tensile and shear strength of the weld joint

Q: 1. Determine bar forces in the truss beldw 30 KN 30 KN 30 N 2m

Q: 200 x 20 mm Plate The strength of the rolled section shown is increased by combining S section,…

Q: A bolted connection shown in figure 3.27 is made up of 150 x 87.5 x 9.5 mm. The angle is made of…

Q: Determine the forces in all members of the truss shown in the figure. Indicate whether in tension or…

A: A truss is given with hinged support at "a" and roller support at "e" A point load of 300lb is…

Q: A welded steel girder having the cross section shown in the figure is fabricated of two 20 in. x 1…

A: If the girder is subjected to a shear force of 495 kips, what force F (per inch of length of weld)…

Q: Problem # 5: The figure shows a roof truss and the detail of connection at joint I. The allowable…

A: Given allowable stresses for shear = 70 MPa, for bearing = 135 MPa…

Q: The allowable unit stress in shear on a fillet weld is 15,000 psi, and the total actual length of…

Question

The beam shown is constructed by joining two pieces of wood together using screws. If the resistant shear force of each bolt is F_t , determine the maximum allowable spacing s between the bolts.

"cte" means constant

"ambas piezas" means both pieces

"sección trasversal" means cross section.

a
3a
E = cte.
(ambas piezas)
tot
Sección transversal

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

?
The strength of the rolled section shown is increased by combining S section, channel, plate and then welded. 1. Determine the location of its centroid; and 2. Determine the moments of inertia of the composite section with respect to its centroidal x and y axes.
X= 482 show complete solutions and FBD
Number of full joints (J1)?
Can u solve me step by step please . thank u
Y1
A truss is supported by two hinges. Which of the following can be removed to form a primary structure? Choices: a. Horizontal component at Hinge 1 b. Vertical component at Hinge 1 c. Vertical component at Hinge 2 d. Any restraint Please provide some explanation. Thank you.
Internal effortsfeatures on a 750 mm sheet wide (made of ASTM A36 steel) were determined using a software basic structure analysis. The effort characteristic requester from a usage overhead is equal to 1260kN. Calculate the thickness needed for the plate? Adopt fyk = 250 MPa and fuk = 450 MPa.Please help Expert sir
4) The beam shown is under simple tension and has a circular section. What are the normal stresses at the four points (a, b, c and d) of the section shown? F Área transversal-A #F
7-35. The boards are glued together to form the built-up beam. If the wood has an allowable shear stress of 7allow 3 MPa, and the glue seam at D can withstand a maximum shear stress of 1.5 MPa, determine the maximum allowable shear V that can be developed in the beam. 50 mm 50 mm 50 mm 50 mm D 150 mm 50 mm B 150 mm Probs. 7-34/35
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem A lap joint is made up of two steel plates 225mm by 10mm. It is connected by seven rivets having a diameter of 22mm snug fit in the drilled holes. The allowable stresses in the rivets and plates are 110 MPa in shear, 220 MPa n bearing and 138 MPa in tension. Use LRFD. Questions: a) Determine the nominal strength for one bolt due to shear. b) Determine the capacity of the plate based on the gross area and effective area.
ASAP!!! NEED RIGHT COMPLETE SOLUTION !!!