For the beam shown, the magnitude of the distributed load is wo = 10.6 kN/m and the beam lengths are a = 6.3 m and b = 18.9 m.(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.(b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine themaximum shear force and the maximum bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter yourshear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If themagnitudes of the largest positive and largest negative values are the same, enter a positive number.WoВa Calculate the reaction forces at A and C.WoAВaAyСуAnswer:kNkN

solution As the free body diagram of beam is given so we can find the reactions by using…

Answered: Calculate the reaction forces at A and…

Engineering

Civil Engineering

Calculate the reaction forces at A and C. Wo A B C а Ay Cy

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Z Z Z I = Ax IM IN Ay By

Q: Assume w₁ = 870 N/m, v W₁

Q: Determine the reactions at supports A, B and C 10KN 6kN Hinge 3kN 12KN.m 2 m 4 m 2 m 2 m 3 m 2 m 幸幸

A: When a force or moment is gereated by external agencies on a body, to counteract that a reaction is…

Q: B 1 A 1/2 IP 1/2 IP 1/2 D A frame ABCD is supported by a roller at A and is on hinge at C as shown…

Q: Determine the components of the reactions for the beam

Q: For the uniform beam shown, use superposition to determine the reaction at each of the three…

A: A simply supported continuous beam is shown in the above figure. A point load of P and another point…

Q: beam is unstable if 3 reactions are parallel to each other O r<3n 3 reactions will meet at a common…

Q: Determine the reactions at the supports of the beam which is loaded as shown.

Q: Beam ABC is under two distributed loads. Point A is a Pin, while Point C is supported by a roller.…

A: Solution: Compute the reactions: RA+RC=12×3×2×102+12×2×1.5×102+1×102=550 N MC=0…

Q: X= 482 Y=82 C=2 SHOW COMPLETE

A: X=482 Y=82 C=2

Q: Engineering Mechanics 1. FIND THE REACTION

A: To find support reaction

Q: Determine the reactions at the supports using the force method. AE is constant. Note: Consider Cx as…

Q: What is the reaction at support C for the beam shown and a settlement of 25 mm at support C

A: Given; Settlement at C=25mm =0.025m E=70GPaE=70×109 N/m2E=70×106 kN/m2I=800×106 mm4I=8×10-4 m4…

Q: 2. Find the reaction at B. Hint: A is a pin, B is a roller 40 lb 50 lb 10 in. 30° 4 in. B 20 in. A

A: Given: L = 20 in H = 10 in Vertical load = 40 lb Horizontal load = 50 lb To find: The reaction at B

Q: B 30° 8. Determine the reaction at B. (Ib) 9. Determine the horizontal reaction at A. (Ib) 10.…

Q: For the given truss below, take P = 20 kN, L=2 m, and H= 6 m to solve the followings: %3D H L 1.…

A: Given P=20kN L=2m H=6m

Q: A 75 mm D B Determine the force in member BD and the co C.

Q: Determine the support reactions at A and D where a = 3m

A: Find the support reactions at A and B

Q: Determine the components of the reactions for the beam

Q: "the reactions of the y 2KN, 2KN 2KN 2m 2m 2m R₂

A: Simply supported beam with multiple point loads is given. We need to determine support reactions

Q: he Reaction at B in the nearest whole number is

A: Reaction of Support A = 80 k Reaction of support B = 100 k

Q: The bell-crank mechanism shown is in equilibrium for an applied load of P(see table) applied at A.…

Q: 2. Use method of members to determine the reactions in the supports and the horizontal and vertical…

Q: The given truss shown is supporting the load R = 108.8 kN on B. The truss has roller support at D…

A: Given: Required: Reaction at D Horizontal reaction at E Vertical reaction at E Note: As per…

Q: 1.) Determine the force in member FE. (N) 2.) Determine the force in member EC. (N) 3.) Determine…

Q: Determine the reactions at A. 5 kip 10 ft 10 ft + 10 ft # 10 ft AV 10 kip 10ft - Skip - 10 kip 10…

A: Given:Required:Support reaction at A

Q: Calculate the reactions at and A for the beam shown. The weight of the beam is 16 Ib/ft. 500 Ib 500…

Q: The mass of the homogeneous flat plate is 22 kg. Determine the reactions in the supports in A and B.…

A: A support reaction is the reaction forces that are attributed to support the system and structures…

Q: Weight of a homogeneous bar AB is 600 lb. Calculate the reactions at supports A and B. 120 vit

A: Given: A simply supported beam carrying a uniformly varying load (UVL). Magnitude of UVL at support…

Q: R₁ 8' W = 5000 lb 12,000 lb 4' R₂

A: A simply supported and uniformly distributed load beam is given.we have to find the support…

Q: F₁ F2 F3 A G 9 H H F D b B b b F₁ = 4kN F₂ = 6kN F3 = GKN a= 5.8m b=3.2m C = 4.8m d = 2.0m

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: Determine the angle θ for equilibrium of the two-member linkage shown. Each member has a mass of 10…

A: Draw the free body diagram.

Q: The compound bean (multiple horizontal beams) is supported by a rocket at “B” and is fixed to the…

A: Given:- To Determine Support Reactions at A, B and C support.

Q: Analyse the pin-jointed grame shown below using the mothod. Salect the in Gorze momber the…

Q: Determine the force in each member of the truss

A: ∑MG=0-HA×4 + 5×2 + 94×4 + 212×6=0HA=414.5 kN →∑H=0HA-HG=0414.5-HG=0HG=414.5 kN…

Q: 6. The upper beam in the figure is supported by a reaction at R3 and roller at A which separates the…

Q: Example 2 Determine the reaction at the roller support B of the beam shown, the support B settles…

Q: Determine the reactions at the supports. 600 N/m 9m 9m 900 N/m In your hand

A: Ay= 9.225 kN By= 8.325 kN

Q: the figure below has the following data: F1=1.7kN, F2=0.8kN, F3=0.58kN, a=1.33 meters, 36 degrees,…

A: While determining the reaction forces of an arch shaped beam , we assume it is a straight beam .

Q: 5) Determine the reactions on joint A. 1.Xm 1.X m 2 m D 6m 3.Y m F = (350j] N B F = (-800k) N Put 8…

Q: Determine the reaction at the roller support in N. 100 N 200N 300 N 45° 30 I m 1 m i O 205 305 285 O…

Q: Consider the structure below, the components of the reaction force at C are Cx = _N. --- 500 N 400 N…

Concept explainers

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.

Question

For the beam shown, the magnitude of the distributed load is wo = 10.6 kN/m and the beam lengths are a = 6.3 m and b = 18.9 m.
(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.
(b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the
maximum shear force and the maximum bending moment.
Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your
shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the
magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Wo
В
a

Calculate the reaction forces at A and C.
Wo
A
В
a
Ay
Су
Answer:
kN
kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the member end moment and reaction of the structure by using kanis method
3 m 3 kN/m B 3 m C 5 kN 1.5 m 1.5 m D The beam has an internal hinge at C. Express your answers in kN. Solve for the reaction at A.
If AC is a two-force member and the magnitude of the reaction at A is 4.63 kN, determine the magnitude of the normal force at a-a. a 4 m A 3.22 m с 3 m B C
Determine the reactions and the force in each member of the trusses shown.USE FORCE METHOD please answer soon and I will like answer.
2. The structure below is supported by a pins at A and D. Determine the pin reactions at A, B, and D. (Hint: You will not be able to solve the equations of equilibrium for the entire structure initially.) A H 3-0" 400 lb 31-D" D TANA 600 lb 2' 0" 6_0"
Determine the reactions at the supports of the beam. Assume that support at B is a roller and EI is constant. 8ft What is Ay in Lbs? 75 Select the correct response: 38.7 200 19.35 B
find all reaction for the frame shown by The slope deflaction method B hinge Fm 2 WL² 12 3 3 find the reaction of the frame by slop deflection method A T 4
a. what is the horizontal component of the reaction of the internal hinge at C b. what is the vertical component of the reaction at the external hinge E
Find the reactive elements and end moment of the beam shown by double integration.
Determine the pin reaction at A and the magnitude and direction of the force reaction at the rollers. 0.5 m W =70 |A |B F_O w kg - 0.4 m 0.4 m 0.4 m -
Solve the reactions and the bar forces .
3. What is the value of the reaction at A in kn?