The beam carries three 40-lb forces, a distributed force, and moment Mo-210 lb-ft shown in the figure. It is held by fixed support at D and by a cable BE that is attached to a counterweight W-90 lb. Assuming frictionless pulleys, determine the reactive forces of the beam. Me 8 lb/ft A 40 lb B 40 lb -4 ft 5 ft с 40 lb D W

The beam carries three 40-lb forces, a distributed force, and moment Mo-210 lb-ft shown in the figure. It is held by fixed support at D and by a cable BE that is attached to a counterweight W-90 lb. Assuming frictionless pulleys, determine the reactive forces of the beam. Me 8 lb/ft A 40 lb B 40 lb -4 ft 5 ft с 40 lb D W

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.15P: The structure is supported by a pin at C and a cable attached to A. The cable runs over the small...

See similar textbooks

Similar questions

The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B, the sag in the cable is 5 m. Find the span L of the cable.
A cylindrical brick chimney of height H weighs w = 825 lb/ft of height (see figure). The inner and outer diameters are d1= 3 ft and d2= 4 ft, respectively. The wind pressure against the side of the chimney is p = 10 lb/ft2 of projected area. Determine the maximum height H if there is to be no tension in the brickwork.
Find support reactions at 4 and Band then use the method of joints to find all member forces. Let b = 3 m and P = 80 kN.
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
2- Find the applied force by the hydraulic cylinder in the truck shown graphically using KS: 1cm=1m, KF: 1cm=1 kN. W=25 kN
4 m 5m 4 m B 4 m 80 kN 60 kN find the forces in members (BC,BE and DE) ? T or C p 10:36
Select the distance a between 2 m and 5 m and the force P between 15 kN and 35 kN in the cage system shown in the figure and find the rod forces. Also note that the forces on the rods did not compress my tension. (AE, AB, BE, DE, CD, BC, BD =?)
The arm in the figure below weighs 41.6 N. The force of gravity acting on the arm acts through point A. Determine the magnitudes of the tension force Ft in the deltoid muscle and the force Fs exerted by the shoulder on the humerus (upper-arm bone) to hold the arm in the position shown. F 0.080 m -0.290 m TE br
2. Find the forces acting at pins C and D of the given frame. loworod slowly onto 2.2 m -3 m 2m DI 3 m3 m- B 4 m 240 N
The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by two cables at B. A force P is applied at B where P = 20i - 14j kN.Note that the reaction force at A acts along the boom because it is a two-force member. Calculate the magnitude of the reaction force at A in kN. Quiz 2. 9, 2 m 17 4 m Finish Time lI 6 m 曲

Determine the force in each member of the truss shown in the figure below. 600 lb 600 lb 600 lb D 300 lb 300 lb 6 ft B E 6 ft Ao H C| F G -8 t- -8 ft -8 ft -8 ft- 8 ft-