The 7442 IC has active _____ (HIGH, LOW) inputs.

Q: An inverter is operated with single pulse modulation and pulse-width is selected to The total…

A:

Q: What are the two primary categories of output circuits in TTL?

A:

Q: Write 8086 Assembly language program to generate Fibonacci sequence. The limit of the sequence is…

A: The question is asking to write an assembly language program for the 8086 processor that generates…

Q: 89 Output voltage of an inverter is controlled by multiple pulse modulation technique. If the peak…

A:

Q: If the a logic IC is powered by 5 V source, and the IC draws 1.3 mA from the source, the total power…

A: Given :   V = 5 volt    I = 1.3 m A    Power of the the IC is given by    P = V . I  The SI Unit of…

Q: In the SCR triggering, the following element used to isolate the high power line from the electronic…

A: As per the guidelines of Bartleby we supposed to answer first question only.

Q: Q3/ Design (64-1) multiplexer by using (8-1) active low multiplexers.

A:

Q: What is the maximum conversion time for a 16-bit dual-ramp converter using a 1-MHz clock frequency?…

A: The maximum conversion time is calculated by using the expression as shown below: Plugging the…

Q: ADC (Analog to Digital Converter) in PIC16F877A operates wi v reference voltage, if the digital…

A:

Q: An analog voltage (0 to 5) volt is to be converted to 8 bit digital form. a. What is the resolution…

A: According to the bartleby's guidelines we have to solve only first three subparts of a question so…

Q: Design and draw a 3 bit Gray code synchronous counter with the state diagram shown below [14…

A:

Q: List 8051's primary characteristics. Explain the basic microcontroller block diagram using a clean…

A: The 8051 Microcontroller is one of the basic types of microcontrollers, designed by Intel in 1980s.…

Q: Discuss the pin diagram of any logic gate? Explain how the NAND gate can be used to derive the other…

A: Note: We are authorized to answer one question at a time, since you have not mentioned which…

Q: KS ) For three input timing diagram shown below, do three of the following logic operations and draw…

A: Timing diagram is drawn for two cycles,as the given waveforms are periodic.for remaining cycles same…

Q: What is interface. What is program block and module block.

A: To verify a design we write verification module and  test bench to check that it meet specification.…

Q: Use the following figure to answer the following question: In this circuit (inverter), the…

A: When the firing angle of the rectifier is less than 30o, the expression for the output voltage for…

Q: Show the schematic of a LUT (using a multiplexer0 which implements the logic for a 3-input AND gate.

A:

Q: Explain in brief the skin effect in power system.

A: In the conductor, the availability of the alternating current at the surface is greater and this…

Q: Total Number of active low pins in IC74LS138? Options A-7 B-8 C-9 D-10

A: The answer is D-10 because For an active high pin, you connect it to HIGH voltage . the Pin having a…

Q: digital electronics 2 In which option is the logic circuit equivalent of the RTL circuit given in…

A: Given :    Here they have mentioned the the sister transistor logic circuit.     From the given…

Q: Write a gate level verilog code for Multiplexer

A:

Q: '8085 Q1: B: Classify instruction according to the addressing modes

A: In this we will write about addressing modes in 8085 processor....

Q: e gate of a JFET is . . based

A:

Q: 3. What is analogue to digital conversion & explain in detail 2-bit quantization.

A:

Q: An SN74AS138 output cannot (reliably)drive an SN74AC08 input when both chips have VCC=4.5 V. Why…

A: According to the datasheet of  SN74AS138 -   At VCC=4.5VThe high-level output voltage is,…

Q: i) Analyse and execute the following 8051 Instructions and specify the output and explain the…

A: As per company guidelines we can solve only first question kindly post another question separately

Q: Question 2 Given Vcc=12V, at first the voltage inputs at Pin 6 and Pin 2 are both 10V. Decide the…

A: The solution is given below

Q: Draw a 3-bit flash converter with Vref= 12V a.Determine the full-scale range. b.Determine the code…

A: The solution can be achieved as follows.

Q: Draw 8259A interfacing connections with 8086 at the address 0744H.

A: The 8259A interfacing connection with 8086 at address 0744h is shown below:

Q: By using the design procedure for digital computers, design the following: i. Encoder ii. Decoder…

A:

Q: Which circuit is normally used to perform serial-to-parallel and parallel-to-serial data conversion?…

A: Transmitting each bit of a code one after the another from LSB to MSB, is called serial…

Q: 1. Determine the corresponding product term per row

A: For the given programmable Array Logic the value of each product term need to be obtained.

Q: hed with power rating than the power demand? O a. Static Switch O b. Inverter O c. Battery O d.…

A:

Q: Q15. An 8-bit ADC set all the output pins high with input voltage of 13.75V driven by 2.25MHZ of…

A: Maximum count value is 28=256 . Given full scale voltage =13.75 volts.

Q: Draw a 3-bit flash converter with Vref= 12 ?. a.Determine the full-scale range. b.Determine the…

A: The solution can be achieved as follows.

Q: The quality of a power suppl-y depends on its __

A:

Q: Generate a time delay of 20 ms with a 16-bit timer 0. (Crystal frequency 10MHz) When the time is up,…

A: Write a program that does:Generate a time delay of 20 ms with a 16-bit timer 0. (Crystal frequency…

Q: (a) Consider the flipflop circuits below: (i) Name the 2 circuits given in the figure. Explain how…

A: We need to discuss the above given question.

Q: (a). If I want to store 4-bit data 0110 and at 4th clock I want to extract all the stored bits,…

A: