The 6-kg bar is released from rest in the horizontal position 1 and falls to position 2. The unstretch spring constant is k = 40 N/m. What will be the bar's angular velocity when it is in position 2.

Q: What about Mohr's circle?

A: In the previous question, Given: The diameter of shaft, d = 20 mm = 0.02 m The maximum bending…

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: Why is it important to determine the slopes and displacements?

A: Slope – when ever any load is applied on the beam due to its elastic properties it bend in very…

Q: What is the part’s over all length?_______________________ 6. Whatisthe part’s over all…

A: considering the detailed drawing of an object to find out the answers of the given questions.

Q: I need answers to problems 4, 5, and 6 pertaining to the print provided.

A: In the given print the length and diameter of the part is to be calculated. Which is mentioned in…

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: What do you mean by method of section?

A: Methode of the section is used to solve the static equilibrium of the strusses. In this method,…

Q: How would tou answer #10?

A: As mentioned in the question to solve #10, i will solve only question 10th

Q: 1.Forging is a process that uses application of force to give shape to metal.

A: Forging is a process that uses application of force to give shape to metal. Answer: True

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: What is areal velocity?

A: The measure of the velocity of one celestial body in orbit to another body which is equal to the…

Q: A 90° elbow shown in Figure 5 (a) is to direct water flow upward at a rate of 50 kg/s. The water is…

A:

Q: The diagram shows a conical section fabricated from pure aluminum. It is of circular cross section…

A: The temperature at  is The temperature at  is The diameter is , The lateral surface are insulated

Q: (a) Figure Q2(a) shown the nut slides down the cord OA. When it is at the midpoint, its speed is 200…

A: Givenspeed=200mm/sAcceleration=10mm/s2

Q: What is the minimum pressure required to reduce volume of a brass sphere by 0.00003 %?

A: Given:reduction in volume=0.00003%

Q: What is the basic unit for length?

A: Solution Length → The measurement of something from end to end is called length

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: what happened with the 10 in the first equation?

A:

Q: 3- Calculate the number of finished goods (output) or N for the figure illustrated below:

A: Given: Total number of goods xi = 1200 Goods accepted after casting = 90% = 0.9 Goods sent for…

Q: What are limits or limits of size?

A: This question belongs to Metrology. Metrology is a science of measurement by using different…

Q: Rocker is an important part related to The starting work piece in steel hot -:which process rolling…

A: Solution:

Q: Q2/ As shown in fig.(2). Prove the main equation for the coefficient of frictional force between the…

A:

Q: B. What is the difference between the critical point and triple point? explain with drawing.

A: GIVEN DATA - TRIPLE POINT AND CRITICAL POINT GIVEN WE HAVE TO EXPLAIN IT WITH DRAWING

Q: The diagram shows a 1 cm3 block that is divided into cubic millimetres. How many mm are there along…

A:

Q: re did you get 1 for m from???

A: Given data as per questionInitially air containsFirst Phase1P1=30 lbf/in2T1=540°FV1=4 ft3Second…

Q: Q1- Compare between the ferrous and non-ferrous metals in terms of the strength, hardness, weight,…

A: Ferrous metals contain iron, and non-ferrous metals don't. That means each type of ferrous and…

Q: Please answer both 1 and 2 as they relate to eachother. thank you in advance

A: Write the properties of 1040 steel.

Q: I have three parts that I need answered pertaining to the print provided below.   What material is…

A: To find the material specified for the part in the drawing, refer Title Block of the drawing.

Q: How far from the lens must the film in a camera be, if the lens has a 32.0 mm focal length and is…

A: Given data as per question Object distance(u) =80 cm =800 mm Focal length(f) =32 mm  Here Location…

Q: Is this for number 1 only?

A:

Q: An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is…

A: SolidWorks is a 3D parametric design software that is used to design all sorts of 2D and 3D parts…

Q: What is the Falling Block?

A: Falling block: The falling block is an action in which a solid metal slides vertically in a grove…

Q: Chill zone consist of smallest equiaxed grains due to low temperature difference between melted…

A: The given statement is false.

Q: What are the concentrated forces?

A: Concentrated forces are more a  mathematical idealizations than a realistic. Force applied at a…

Q: Choose forming and generating operation 2 po Work Work Threa dsad dsa Generated surface Work Work…

A: This is taper turning

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.