How far from the lens must the film in a camera be, if the lens has a 32.0 mm focal length and is being used to photograph a flower 80.0 cm away?

Q: Can you please help me with this isometric drawing?   Please make sure the drawing is easy to…

A: According to the details provided in the question, we need to draw an isometric view.

Q: Q5: At the instant shown in figure (5) 04 = 6 rad/s, pulley A is given an angular acceleration a =…

A: Given data: The radius of the pulley A is rA=60 mm=0.06 m The initial angular velocity of the pulley…

Q: Draw the third projection

A: Please refer the following image for the missing view.

Q: -Which of the following options represents the stereoscopic shape of the projections in the figure?…

A:

Q: find the top view, right side view, front view and the figure (isometric/oblique drawing)

A: Given:- Front and side view of a part Scale=10mm   To find:- To draw Front view, Right side view,…

Q: (a) The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o…

A:

Q: The following is a schematic diagram of the Charpy impact tester. Is from the following. At this…

A:

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Is it possible to proved clear copy, this one is blurry. Th

A: In this problem, it is asking to write the solution in clear way.

Q: 4. Design a Keplerian or astronomical telescope that will produce an 80x magnification. What factors…

A: Given data: The length of tube is L=46.5 cm. The focal length of eyepiece is fe=1.7 cm.

Q: An automobile company displays a die-cast model of its first car, made from 9.35 kg of iron. To…

A:

Q: 5kN 2kN-m 1kN/m 1.2- 1.2 t1.2 -2Am B

A: It is required to determine reaction force at support A and B

Q: Draw an archemedian spiral of 1½ convulations with the greatest radius of 100mm and the smallest…

A: It is the locus corresponding to the locations over time of a point moving away from a fixed point…

Q: Create a free hand isometric drawing of the three objects

A: Free hand isometric drawing of all three components are drawn below...

Q: 31.) In the same diagram, what is the direction of the line EA? a) [0īī] b) [111] c) [110] d) [010]

A:

Q: ᴀ 4' ʜɪɢʜ, 3' ᴅɪᴀᴍᴇᴛᴇʀ ᴛᴀɴᴋ ᴡʜᴏꜱᴇ ᴛᴏᴘ ɪꜱ ᴏᴘᴇɴ ᴛᴏ ᴛʜᴇ ᴀᴛᴍᴏꜱᴘʜᴇʀᴇ ɪꜱ ɪɴɪᴛɪᴀʟʟʏ ꜰɪʟʟᴇᴅ ᴡɪᴛʜ ᴡᴀᴛᴇʀ. ᴛʜᴇ…

A:

Q: Q) Draw the following projections for the figure shown with scale 1:1. 1. Front View 2. Side View 3.…

A: Solution:

Q: A) L-mR - mgRcos B) -mtở - mgR L = C) L=mRo - mgRcos@ D) L=mi6 – mgRcose O A Ов Ос

A:

Q: Sketch the orthographic view

A: Solution: The front, top and side views are shown below:

Q: Using a lens with unknown magnification, the ocular reticle measures 0.7 mm in length. What is the…

A: When you look through the microscope, the reticle picture is superimposed over the image of your…

Q: Macroscopic examination is distinguished from microscopic examination by: The low magnification…

A: Macroscopic examination is distinguished from microscopic examination by: The low magnification…

Q: Q4/ classify the types of defect depending on its dimensions

A: Based on the dimension, the crystal defects are classified as  1. O-Dimensional defects 2.…

Q: The projection below is the projection of two figures, what are ?they

A: There are two figures possible as shown below

Q: The simply supported beam ABC has the rectangular cross-section as shown in Figure Q2. The beam…

A:

Q: A 200 µm spherical particle has been fixed to a spatula using super-glue and has been very slowly…

A:

Q: In the appendices, the modulus of elasticity for silicon nitride is 304 GPa (that of steel is 207…

A:

Q: The theoretical failure strength is significantly higher than the empirical failure strength of…

A: Deformation in the polycrystal grains is similar to that of single crystal. The mechanism of the…

Q: Can you please describe these terms: topocentric right ascension and declination, azimuth,…

A: Step 1: Identify that right ascension and declination coordinates are fixed on the global sky…

Q: G. A line 32 mm long joins to towns on a map of scale 1:100,000. (a) How far apart are the towns to…

A: For solution refer below images.

Q: Note: (1) n is the student's number in the class. (2) All dimensions are in cm. (3) Dimensions need…

A: An Engineering drawing is a technical drawing.It purpose is to give information of the product for…

Q: * 14. An entomologist observes a 1-mm-long bug with a lens of focal length 5 cm. a) The bug is…

A: GivenSize of object=1mmFocal lengthf=5cm

Q: A line in a drawing is 3 inches long, when measured.  If the drawing scale is 20:1, how long is that…

A: Given Data The length of line is:3 inches The drawing scale is:20:1 To find: The actual length of…

Q: ᴄᴏᴍᴘᴜᴛᴇ ᴛʜᴇ ᴍᴀxɪᴍᴜᴍ ᴅᴇꜰʟᴇᴄᴛɪᴏɴ, ɪɴ ɪɴᴄʜᴇꜱ, ᴏꜰ ᴀ ꜱɪᴍᴘʟʏ-ꜱᴜᴘᴘᴏʀᴛᴇᴅ, 2-ꜰᴛ ʟᴏɴɢ, ᴀɪꜱɪ ᴄ1020, ᴀꜱ ʀᴏʟʟᴇᴅ,…

A:

Radiation

Radiation can be described as the energy in the form of a particular matter or electromagnetic waves traveling in the air and can be in the form of light, sound, and heat. Radiation can be detected through special instruments like X-rays. The radiation from a cooler object is less intense as compared to the radiation from hot objects.