The 50-lb lamp is supported by two steel rods connected at A. The diameter of rod AB is 0.5 in. and the diameter of rod AC is 0.4 in. and the average normal stress in rod AC is twice the average normal stress in rod AB. What is the angle of orientation (in degrees) of rod AC? Determine the axial loads (Ib) and stresses (psi) in the two rods? B 60°

Q: Find bending at point B using the Castigliano method.

A:

Q: Conduction An aluminum rod and an iron rod of equal length 2.0 m and cross-sectional area 2 cm? are…

A:

Q: A 37.5-mm-diameter rod 6 m long elongates 12 mm under a load 236 KN. The diameter of the rod…

A:

Q: the Torsion and, peoot Explain Formula Suitable of to ilth the help diagram ?

A: Torsion equation or torsion constant is defined as the geometrical property of a bar’s cross-section…

Q: 118. Medical The bones of the forearm (radius and ulna) are hinged to the humerus at the elbow…

A:

Q: une at F = 5.5 kN (Figur

A: solution as follows

Q: Question (5): (a) The device shown in Fig. (5-a) is designed to apply pressure when bonding laminate…

A: Given Data At the handle 120N force is applied  Let us draw the reaction at the roller supports

Q: In the Figure below, the tensile breaking strength, (sigma mark)tenstile-breaking = 140 Mpa…

A: Given: The tensile strength of the material = 140 Mpa The compressive strength of the material = 460…

Q: fimm. For the spring assemblage shown in the figure above, determine the displacement at node 2 and…

A: The value of spring constant is The displacement of node 3 is

Q: 2) A 1 in Dia x 3 in long mild steel hammer head is to be heat treated for surface hardening. If the…

A:

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: With respect to flange-gasket-bolt/nut system following specifications are given. If the Gasket is…

A: Given: The outside diameter of shell, Ds = 90 cm The shell thickness, t = 8 mm = 0.8 cm The…

Q: 1. Create a free-body diagram for the above condition and apply the sign convention for forces and…

A: Mass of the man, mass of the box, angle in horizontal plane,the distance from the center of the…

Q: Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully…

A:

Q: Iwo concentric springs are constructed with squared and ground ends from oil-hardened steel. The…

A: Given:The ultimate strength, Sut = 204,000 lbf/in^2The yield strength of steel, Syt = 0.75SutThe…

Q: Give me right solution with clear calculations Question-3: - Initial error of the impact tester is…

A:

Q: What are the two basic failures/limit states of tension members and discuss? Derive the allowable…

A: Given question : What are the two basic failures/limit states of tension members and discuss? Derive…

Q: A steel bar AD has a cross-sectional area of 260 mm² and is loaded by forces P, = 12 kN, P, = 8 kN,…

A:

Q: Compute the stress in the bar.

A: Here,  is strain developed in the bar. is compressed length. is initial length of the bar.. is…

Q: 3.8 The discs in the spinal column can withstand a stress (force per unit area) of 1.1 x 107 N/m2…

A: Given dataStress in the spinal column σmax = 1.1(10)7 N/m2Cros sectional area A = 10cm2= 10-3m2To…

Q: GIVEN: Diagram shown below [Note: you do not have to re-create the GIVEN diagrams; work must be on…

A:

Q: The rigid, horizontal slab is attached to two identical copper rods. There is a 1. gap a = 0.18 mm…

A:

Q: Determine the height h above the base of the centroid of the Assume a = 10.27 in., b = 12.07 in., c…

A:

Q: Unlike the tensile effort, which tends to straighten the parts, the compression effort tends to…

A:

Q: Mention with explanations three applications of Bernoulli's principle

A: What is Bernoulli's principle? This Bernoulli’s principle formulated by Scientist Daniel Bernoulli…

Q: 5. When unloaded, bars AB and AC are each 36 - in long and have a cross-sectional area of 2 in.…

A:

Q: FIGURE 3.16 Tension test on a round steel specimen showing grips and an exten- someter with an LVDT.

A: Given:

Q: (6) There are many kinds of polyethylene foam, each with different properties. The low density…

A: Given: The torque, T = 2 kN.m The elastic modulus, G = 6 GPa The diameter, d = 300 mm The length, L…

Q: Instructions: Write your solution and answer on a LBP/SBP/newsprint/yellow paper. Put your name and…

A:

Q: ---- at the end of the fire grate which is utilized in deflectin 7. In a Lancashire steam boiler,…

A: Disclaimer: Since you have asked multiple question, we will solve the first question for you. If you…

Q: What is the concept of ALARP? Give an example of a situation where the ALARP principle is applied.…

A: In this problem, we have to discuss the concept of ALARP with an example.

Q: Q) For the below figure (1), Find the magnitude of force required to rolling the cylinder over the…

A:

Q: 120 MPa in compression. (The working stress in compression is smalle to reduce the danger of…

A:

Q: Problem 208 A steel tire, 10 mm thick, 80 mm wide, and 1500.0 mm inside diameter, is heated and…

A: Given Data: Thickness t=10 mm Wide b=80 mm Inside Diameter di=1500 mm After heating final diameter…

Q: Why are we assuming values for h? And where does the critical force come from?

A: The h indicates the thickness of the link OB. In question, we need to determine the thickness of the…

Q: 3. A 30-cm long, 12-mm diameter carbon steel rod was subjected to 15,5 kN of tension. Calculate (a)…

A:

Q: A uniform plank 9m long of mass 80 kg is horizontal. It is supported by vertical strings attached at…

A: