With respect to flange-gasket-bolt/nut system following specifications are given. If the Gasket is made from corrugated soft copper, calculate the minimum thickness of flange. Outside diameter of shell = 90 cm; Shell thickness = 8 mm; Operating pressure = 8 kg/ sq.cm; Design temperature = 150°C; Inside diameter of gasket = 94 cm; Gasket width = 1.6cm; Gasket seating stress y=310 kg/ sq.cm; Permissible stress for the bolt material = 980 kg/ sq.cm; Permissible stress for the flange material = 980 kg/ sq.cm. Total of 28 bolts of 17 mm diameter are to %D be used to tighten the flange joint.

With respect to flange-gasket-bolt/nut system following specifications are given. If the Gasket is made from corrugated soft copper, calculate the minimum thickness of flange. Outside diameter of shell = 90 cm; Shell thickness = 8 mm; Operating pressure = 8 kg/ sq.cm; Design temperature = 150°C; Inside diameter of gasket = 94 cm; Gasket width = 1.6cm; Gasket seating stress y=310 kg/ sq.cm; Permissible stress for the bolt material = 980 kg/ sq.cm; Permissible stress for the flange material = 980 kg/ sq.cm. Total of 28 bolts of 17 mm diameter are to %D be used to tighten the flange joint.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve it right away systematically. SHOW FBD. Clear and complete solution please thank you
Two shafts A and B are connected by rolling cones and turn in the same direction. A makes 250 RPM while B makes 90 RPM. The shaft angle is 30 degrees. Calculate the cone angle of each cone and the diameter of each base if the base of cone B is 2 inches from the vertex. Solve also graphically
Quick & simple answer
For the steel shaft shown in Fig. Draw a torque diagram for the shaft. 150 ft-lb 100 ft-lb 300 ft-lb
solve 15 mins plzz i'll give you multiple upvote.. hand written plz
Create your own 2 problems about couple forces with complete solution
State the number of DOF and its type for each robot shown in Fig.1: A-------- D ‒‒‒‒‒- LR 200 B-- SHOULDER TRUNK E X ----- WAIST 320 (JOINT 1) UPPER ARM FOREARM WRIST C------- SHOULDER 200 (JOINT 21 ELBOW 284 (JOINT 3) WRIST ROTATION 200 (JOINT 4) BEND 2009 (JOINT SI FLANGE 632 (JOINT ) Biz 1. BUMA 550 sobre arm. Derses of scint roustion and member identifincion Fig. 1 ACO₂ P₁
A1 A grinding wheel used in machine shop needs to be analyzed in terms of its suitability for a specific grinding task. Find 1. Accelerating torque produced by the grinding wheel II. Increase in angular momentum of the grinding wheel II. Increase in Kinetic energy of the grinding wheel. Assume the following data Suitable mass of the grinding wheel. Suitable radius of grinding wheel. Select any two Speeds between range 1000 – 3000 rpm. Consider 20 seconds time gap between two speeds selected. 1. 2. 3. 4. Justify your data assumptions.
Hand written plz asap... I'll give you multiple upvote hand written plz... Plz solve it within 1 hour plzzz fast...
The power and motion can be transmitted from one shaft to another shaft by means of gear drives if center distance between the shafts is very large. Select one: O True O False
Adjustable Link L m Pivot Pivot Screw 'B' Gripper In the drawing, arm A is being driven back and forth in the direction of the arrows. It is connected to a gripper by way of an adjustable link L, two horizontal bars and two vertical bars. Screw B is a shoulder screw secured to arm A, but allows the horizontal bar to pivot around it. If the shoulder screw B was lowered towards the end of arm A, and the stroke of arm A remained the same, the stroke of the gripper would: Arm 'A' 0 MIMINIA
The figure below shows the components of normal forces, the value of radial force on the gear wheel due to a tangential force of 642 N is . N, Take pressure angle as 140. PN Pitch point Gear driven 02 The radial force is