The 46-mm diameter shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. The pulleys C and D are subjected to the vertical and horizontal loadings shown in the figure below. (Figure 1) Part A Determine the absolute maximum bending stress in the shaft. Express your answer to three significant figures and include the appropriate units. ? Omax = 10.7 MPa Submit Previous Answers Request Answer X Incorrect; Try Again; 29 attempts remaining Provide Feedback Figure < 1 of 1> 150 N 400 mm 150 N 300 N 300 N 400 mm 400 mm

The 46-mm diameter shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. The pulleys C and D are subjected to the vertical and horizontal loadings shown in the figure below. (Figure 1) Part A Determine the absolute maximum bending stress in the shaft. Express your answer to three significant figures and include the appropriate units. ? Omax = 10.7 MPa Submit Previous Answers Request Answer X Incorrect; Try Again; 29 attempts remaining Provide Feedback Figure < 1 of 1> 150 N 400 mm 150 N 300 N 300 N 400 mm 400 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Similar questions

A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) Figure 1 m 1 m 30 mm 40 mm B - 1 m D 1 of 1 Part A If P = 22 kN, determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μA Value Request Answer Units ?
PROBLEM: A shaft supported at the ends carries a spur gear and is to transmit 10 kW at 200 rpm. The weight of the gear is 1 kN. If the allowable shear stress is 45 MPa, determine the shaft diameter. FIGURE: Bearing 150 mm 100 mm. 200 mm. Gear Shaft 100 mm Bearing SOLUTION: Instructions: Solve the diameter of the shaft. To add an equation in Word, select Insert > Equation or press Alt + = Example: = F A
Rev Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = Value Units Figure 1 of 1 Submit Request Answer Provide Feedback 1 m 1 m 1 m 30 mm 40 mm
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
Part A The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) If P = 20 kN , determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. HA ? Tmax = 363.89 |MPa Figure 1 of 1 Submit Previous Answers Request Answer Provide Feedback 1 m 1m 1m 30 mm 40 mm
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. (Figure 1) Figure 1 m 1m- 30 mm 40 mm 1m P 1 of 1 > Part A If P = 22 kN, determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. Trung = 9.87 μÀ MPa Submit Previous Answers Request Answer Provide Feedback ? X Incorrect; Try Again; 5 attempts remaining
Problem:1 A solid circular shaft is subjected to a bending moment of 3000 N-m and a torque of 9000 N-m. The shaft is made of 45 C 8steel having ultimate tensile/ bending stress of 850 MPa and a Ultimate shear stress of 650 MPa. Assume a factor of safety of 10. Determine the diameter of the shaft from both theories.
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you