6-122 Segment A of the composdte heam is made from 2014-T6 aluminum aloy and segment B A-36 steel. If w - 0.9 kip/, determine the absolute maximum bending stress developed in the aluminum and stel. Skelch the stress distribution on the cross section. 6-123. Segment A of the composite beam is made from 2014-T6 aluminum alloy and segment Bs A36 steel. The alowable bending stress for the aluminum and steel are (l-15 ksi and (ol-22 ksl.Determine the maximum alowahle Intensity w of the uniform distributed kuad. 15 h Probs. 6-122123

6-122 Segment A of the composdte heam is made from 2014-T6 aluminum aloy and segment B A-36 steel. If w - 0.9 kip/, determine the absolute maximum bending stress developed in the aluminum and stel. Skelch the stress distribution on the cross section. 6-123. Segment A of the composite beam is made from 2014-T6 aluminum alloy and segment Bs A36 steel. The alowable bending stress for the aluminum and steel are (l-15 ksi and (ol-22 ksl.Determine the maximum alowahle Intensity w of the uniform distributed kuad. 15 h Probs. 6-122123

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.11.11P: The three beams shown have approximately the same cross-sectional area. Beam 1 is a W 14 X 82 with...

See similar textbooks

Similar questions

Hwi Abeam had subjected to a postive bending moment of 5 KN.m. Thc Coss-Sedional dimensious are shown below. Draw the bending stress distribution ou the Cross- sedion. loo mm 15 mm T 3 mm
"6-120. The composite beam is made of steel (A) bonded to brass (B) and has the cros section shown. IIt is subjected to a moment of M - 65 KN - m, determine the maximum bending stress in the brass and steel. Alsa, what is the stres In cach material at the seam where they are bonded together? E- 100 GPa, E-20O GPa. 6-12L The composile beam is made of steel (A) bonded to bras (8) and has the cros section shown. II he alkwable bending stress far the sted is (oae- 180 MPa, and for the bras (oa-0 MPa, delermine the matimum moment M that can be appiled to the beam. -100 GPa, E-200 GPa Imim Y 200 mm 175 m Probs. 6-12121
The cantilever beam A CB shown in the hgure is subjected to a uniform load of intensity q acting between points A and C. Determine the angle of rotation ÔAat the free end A>(Obtain the solution by using the modified form of Castigliano's theorem.)
The rod is supported by smooth journal bearings at A and B that only exert vertical reactions on the shaft. Part A Determine its smallest diameter d if the allowable bending stress is oallow = 130 MPa (Figure 1) Express your answer with the appropriate units. HA ? d = Value Units Figure < 1 of 1 Submit Request Answer 12 kN/m Provide Feedback 3 m 1.5 m
A leaf spring 75 cm long is required to carry a central load of 8 kN. If the central deflection is not to exceed 2 cm and bending stress no greater than 200 MPa, determine the thickness, width and number of plates. Also compute the radius to which plates should be curved. As- sume width of plate to be 12 times its thickness and E = 200 GPa.
. A composite beam, made of aluminum (Al) and magnesium (Mg), has the cross section shown below. The moduli of elasticity for aluminum and magnesium are EAI = 70 GPa and EMg = 45 GPa, respectively. If the allowable flexural stresses (in tension and com- pression) are All 135 MPa for the aluminum and Mg 120 MPa for the magnesium, determine the maximum allowable bending moment for the beam. all - 0.2 m 0.2 m Al 0.2 m Mg C
14 in 14 in. 4. Use dhe freebuly diagranppch n a Sectua nd bending moment at any specifed paint inabam Wate ouations for all segnentsd the sharing face Ind bending moment dagrams uNing the guideliapre sented an Section 5-10,
Part B - Moments of inertia of the cross section with respect to the y- and z-axesTo calculate the absolute maximum bending stress in the member using the flexure formula for unsymmetrical bending, the moments of inertia of the cross section must be calculated. Select the correct formulas for these values. Iy=? Part C - Neutral-axis angle due to externally applied momentsThe neutral-axis angle of the cross section being analyzed is the axis along which there is a zero stress value. Determine the neutral-axis angle, α, due to the externally applied moments as measured counterclockwise from the positive z axis in the yz plane.Express your answer to three significant figures and include the appropriate units. α=? Part D - Absolute maximum stress in cross section ABCDDetermine the absolute maximum stress, |σmax|, in cross section ABCD due to the two externally applied moments. |σmax|=?
5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E-200 GPa and BD from aluminum with E-70 GPa. The diameters of posts AC and 80 are 25 mm and 40 mm, respectively. Determine the vertical displacement of point on AB 100 KN 400mm D 6. The timber beam has a cross-sectional area of 2000 mm and its modulus of elasticity is 12 GP Axial loads are applied at points B, C, and D as shown. Calculate the total change in length of the beam. Answer: 2.33 mm 40 KN 35 KN 20 KN 3.20 m 1.60m 3.20 m
The axle of the freight train is subjected to loadings as shown below. The diameter of the axle is 137.5 mm. If it is supported by two journal bearings at C and D, determine the maximum bending stress. Include a FBD, SFD and BMD using either the section or graphical method. Draw a cross-section of the shaft and indicate the points of maximum tension and compression. A B 250 mm 100 kN 1500 mm- Answer 0= +98 MPa 250 mm 100 kN
Fi-9 II the heam ts suhjecied to a bending moment of M= 20 EN-m delemine the mimum bending siress in the beam. 20
F6-9 II Lhe heam is suhjecied to a bending moment of M= 20 N-mL determine the manimum tending sires In the beam. 200mm 20 20m F6-18. the heam is subjeced lo a bending moment of M= 50 EN - m. skeich the hending siress disiribution over the beam's croSS Seclion. 30 mm 150 mm 130 ma