The 3-phase half-wave diode rectifier feeds a load consisting of a 50-ohm resistor. The sinusoidal sources in the input of the rectifier are wye-connected and phase-to-phase rms voltage is 380 volts. Calculate the power (in watts) absorbed by the load. Assume the diode is ideal. a. 680.36 b. 2267.90 C. 4082.20 d. 1700.90 e. 1360.70

The 3-phase half-wave diode rectifier feeds a load consisting of a 50-ohm resistor. The sinusoidal sources in the input of the rectifier are wye-connected and phase-to-phase rms voltage is 380 volts. Calculate the power (in watts) absorbed by the load. Assume the diode is ideal. a. 680.36 b. 2267.90 C. 4082.20 d. 1700.90 e. 1360.70

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
For the circuit shown in the Figure, if the diodes are silicon diodes with Vp(on)=0.7 V, and VIN=50 sin wt V, V1 =6 V and V2 = 16 V, then the value of VouTP-p) is: R, D VaN Vout v1事 2章 Oa. 25.4 V Ob. 27.4 V Oc. 29.4 V Od. 23.4 V
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
If the PIV rating of the diodes in the figure is increased, the current flowing through the RL Please choose one: a. increase b. constant c. reduction
A single-phase, full-wave diode bridge is used to supply power to a resistive load of value R = 75 2. If the supply voltage is sinusoidal, Vs 400 sin ot, calculate the average and rms values of the load current. Calculate the ripple factor for the load current and compare this with half- wave operation. =
ii) Analyse the circuit shown in below Figure. 2, assume diodes as silicon diode. Calculate: a. Vout b. IR3 c. Ip2 VCC 16V D1 D4 V3 10 V R1 2.2kQ D5 D2 Vout R3 2.8kQ IR3 Ip2 R2 4.7 kQ D3 V1 2.2 V V2 15V
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.