Temperature distribution along the radius of a long cylindrical shell was found to be -2596.8 W/m2; -1558.1 W/m2; T(r) = 365 +21.64 ln(r) all quantities in SI units. inward Since the temperature is only dependent on radius (r), the heat transfer in this case is radially one- dimensional. The thermal conductivity of cylindrical shell is 36 W/m-K. The shell has inner diameter of 0.5 m and outer diameter of 1 m. Find out the heat flux at r = 0.3 m and at the outer surface of the tube. Justify if the heat transfer is radially outward or radially inward.

Temperature distribution along the radius of a long cylindrical shell was found to be -2596.8 W/m2; -1558.1 W/m2; T(r) = 365 +21.64 ln(r) all quantities in SI units. inward Since the temperature is only dependent on radius (r), the heat transfer in this case is radially one- dimensional. The thermal conductivity of cylindrical shell is 36 W/m-K. The shell has inner diameter of 0.5 m and outer diameter of 1 m. Find out the heat flux at r = 0.3 m and at the outer surface of the tube. Justify if the heat transfer is radially outward or radially inward.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal conductivity k = 40 W/m-K and a thickness L = 0.3 m, with no internal heat generation. -T2 L Determine the heat flux, in kW/m², and the unknown quantity for each case. Case T1(°C) T2(°C) dT/dx(K/m) q (kW/m?) 1 50 -20 i i 2 -30 -10 i i 3 70 i 160 i 4 i 40 -80 i 5 i 30 200 i
i need the answer quickly
HEAT TRANSFER A 30 ft. long and 2 inch nominal diameter and outsidediameter of 2.375 in pipe is covered by a 1 inch thickinsulation (k = 0.0375 Btu/hr.ft.°F). Determine the heatloss if the inner and outer temperatures of the insulationare 380°F and 80 F, respectively. SHOW COMPLETE SOLUTION IN A PAPER.
I need the answer as soon as possible
A hot water pipe is 100 mm in diameter and 80 m long. This pipe is insulated in two layers. First layer is 25 mm thick, thermal conductivity is 0.12 W/m C material, second layer is 45 mm thick It is made of material with a thermal conductivity of 0.05 W/m C. T1, T2 and T3 are the surface temperatures in the pipe. One With the acceptance of heat transfer in dimensional and continuous conditions, transfer from the pipe in case T1= 600 OC and T3= 35 C Find the amount of heat released and the temperature T2. 2.tabaka 1.tabaka 100 mm T₁ T₂ T3
Consider 1D heat conduction in a Cu rod with an average temperature of 25C. Does there exist a maximum (or upper-limit value) temperature gradient for heat conduction. If so, what is that value with justification on the derivation/scientific reasoning. The thermal conductivity is k=385 W/m*K. The diameter of the rod is left in terms of d.
Unit of thermal conductivity in S.I. units is (a) J/m2 sec (b) J/m °K sec (c) W/m °K (d) (a) and (c) above (e) (b) and (c) above.
The wall of a furnace comprises three layers as shown in the figuie. The first layer is tery (whose maximum allowable temperature is 1400°C) while the second laver is Tracto:y Chose maximum allowable temperature is 1093°C). The third layer is a plate of 6 35 od thermal contact. Steet plare To 6.35x3 45A 1370 C Concerntiation veluciy 37.8 C mass Siynes Figure. Layers in a composite furnace wall. e temperature To on the inside of the refractory is 1370°C, while the temperature T; on the side of the steel plate is 37.8° The heat loss through the furnace HnIlisexpectet tobe
Please help me its urgent solve correctly please
Determine the resistance of an aluminium coil of 183 cm as diameter consists of 14500 turns and the mean length per turn is 4883 cm. Take the electrical conductivity of the aluminium coil as 0.37 MS/m. Solution: Area of Cross-section of the Coil (in m²) Total Length (in m) The Resistance of the Coil (in 2) o search