Task#1 1) Draw a truth table for half adder. Clearly mention inputs and outputs. 2) Write the SOP and POS Expression. 3) Write the Minimized POS using K-Map using grouping technique. 4) Implement half adder on Circuit Maker and verify the results. 5) Draw the block diagram of the above half adder (on page).

Task#1 1) Draw a truth table for half adder. Clearly mention inputs and outputs. 2) Write the SOP and POS Expression. 3) Write the Minimized POS using K-Map using grouping technique. 4) Implement half adder on Circuit Maker and verify the results. 5) Draw the block diagram of the above half adder (on page).

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Electrical Engineering Draw 2, 1 bit ALUS to create a basic 2 bit ALU. the carry out and carry in bits must ripple across. The ALU should subtract/add, logical NOR, logical AND, and logical OR. Draw out the adding logic circuit
The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
Given the K map find the expression and logic circuit.Use a plain sheet of paper or screen capture simulation circuit like Cedar Logic or LSP to draw the circuit.
(c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).
the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus.
Answer the following questions: 1. Design a 8 bit "shift left-shift right" register. 2. Design a 8 bit up counter. 3. Difference between sequential circuit vs combinational circuit. 4. Design a 8:1 multiplexer using 4:1 multiplexer and 2:1 multiplexer. 5. When designing register file, we used multiplexer to read from a specific register of that register file. However, to write in the register file, we didn't use demultiplexer. Why ? 6. In our designed register file, we can write one data at a time. But if we want to write two data at a time,what should we do ? 7.Logisim simulation: A. Design a 8 bit register file with 10 registers. B. Design an ALU with AND, OR, XOR, NOT, ADD and SUBTRUCT operations that can use the above register file. C. Create a single cycle data-path between register file and ALU. Save 1 digit of your NSU ID in each register of your register file before running instructions given below.E.g. for id: 1831565042, save 1 in first register, 8 in second, 3 in third and…
ehcu.org/pluginfile 100% 10 / 11 locations, count how many times is 0 and how many times 1 is. Questions:- 1- Write a program in assembly language to perform the following logic ci BL CL DL [5100]- 2- How we can perform the NEG and NOT instructions by using different instructions. 3- Write the following program by using different instruction or instructions for each instruction on the program. MOV AL , 00 MOV BX , FFFF XOR CL , FF NEG BYTE PTR [DI] AND CX , LG
Solve the problem and simplify the output function using Quine–Mc Cluskey Methods. The following requirements must be met in solving the problem. Requirement:a. Truth Tableb. Timing Diagramc. Quine – Mc Cluskey Method d. Logic Diagram A private company wants to decide on a certain issue. Each of the four officials has an equal share of voting right. At least two of them must approve the solution in order to implement it. Each of them has a switch which closes to vote YES and open to vote NO.
DISCUSSION: 1- Is the Gray code arithmetic code? Why? Where this code usėd? 2- What is the parity bit? 13- Design five - bit odd parity checker? 4- a) What are the main applications of the comparator? /b) Design two – two bit comparator. -5- Convert five.bit Gray to binary code, write truth table and draw the circuit diagram. 2-5
What is a Ripple counter? Draw the circuit of a 2 bit ripple counter.
Design the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by one
For given logic circuit, a)Build the math model. b)Configure the truth table.