A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high the entire mass is 3000kg and encountered an unbalanced force of 15 kN. Estimate the angle of spill in degrees
Q: The manufacturing of pie fi lling involves blending of concentrated product with liquid sugar and h...
A:
Q: A cylindrical tank holding oxygen at 1,434 kPa pressure has an outside diameter of 389 mm and a wall...
A:
Q: body weighs 1000 lbf when exposed to a standard earth gravity g = 32.174 ft/s2. (a) What is its mass...
A: Given Data W=1000 lbf g=32.174 ft/s2 gm=1.62 m/s2
Q: A cube container with a dimension of 3m on each side is 60% full of water (density=1000kg/m^3). The...
A: Given Side, d = 3 m Density = 1000 kg/m3 Force, F = 25 kN Find Acceleration, a
Q: The gas is compressed from an initial state o 0.35 m and 105 kPa to a final state of 0.14 m and to t...
A: Given: Isobaric compressionInitial volume of gas, V1=0.35 m3initial pressure of gas, P1=105 kPaFinal...
Q: A fabricated assembly made from three different sizes of standard steel tubing is shown below. The l...
A: Given dataIncoming Flow rate of water = 0.072 m3/sThere are two branchesBranch 1 has a velocity of ...
Q: Current Attempt in Progress The rear window of an automobile is defogged by passing warm air over it...
A:
Q: A 3 kg box is sliding across a frictionless table at a rate of 5 m/s. It encounters a 35° incline wi...
A:
Q: Knowing that oall = 24 ksi for the steel strip AB, determine: (a) the largest couple M that can be a...
A: When a beam is subjected to pure bending couple M then there exists bending stress in the beam and i...
Q: 750 ml of a gas is at 185 kPa gage pressure and 64 °C. Determine the number of molecules in the ga...
A: Given Data: The volume of the gas, V=750 mL The pressure of the gas, P=185 kPa The temperature of t...
Q: 1. What is the standard equation of the parabola y + 6x +4y – 2 = 0? A) (y+2)² = -6(x – 1) B) (y+2)?...
A: The standard equation of the parabola is (y+2)2 = -6(x-1). Therefore, option (A) is correct answer.
Q: The compressive Stresf () of a rectangular beam sectionis given by the fakmutas P bh 6 M bh? where M...
A:
Q: Need your help. List atleast 3 possible title for Machine Design and for Thesis 1
A: given; Need your help. List at least 3 possible title for Machine Design and for Thesis 1.
Q: A thin-walled cylindrical pressure vessel ofa radius r is subjected simultaneously to internal gaspr...
A: A cylindrical vessel or shell may be thin and thick depending upon the thickness of the plate in rel...
Q: What mechanism of creep can be prevented using a single crystal part? Justify your answer using suit...
A: The creep can be prevented or the creep resistance can be improved by using a single crystal part. I...
Q: A boiler produces 5000kPa steam which is 67% dry, from boiler feed water @ 100°C. flow rate is 960 k...
A:
Q: If water at 180°F is flowing with a velocity of 4.50 ft/s in a standard 6-in Schedule 40 pipe, calcu...
A: calculate the weight flow rate
Q: obtained from the test: i. Diameter of the steel bar = 30 mm ii. Gauge length of the bar = 200 mm ii...
A:
Q: Q/Draw the complete shearing force and bending moment diagrams for the beam shown in Figure below 10...
A: Draw the given free-body diagram. Apply force equilibrium in vertical direction. R1+R2-10 kN/m5 m=0...
Q: Determine the weight in newton [N] of a car whose mass is 1500 kg. Convert the mass of the car to sl...
A: Given Data m=1500 kg
Q: Ratio of the temperature?
A: Given; Total emmisive power of a surface is; ∈1=500 W/m2At a given temperature=T1∈1=1200 W/m2At a te...
Q: 4. Rod OA rotates about O in a horizontal plane. The motion of the 0.5-lb collar B is defined by the...
A:
Q: Air flows steadily through an air compressor at a rate of 28 kg×min-1 with a velocity of 12 m×s-1 at...
A: Answer: (1) The rate of shaft work is -130.1112 kW. (2) The ratio of inlet pipe diameter to outlet p...
Q: A 150-lb wrecking ball B is attached to a 40-ft-long steel cable AB and swings in the vertical arc s...
A: Given data as per question w=150 lbL=40 ftθ=150
Q: Consider steady-state conditions for one-dimensional conduction in a plane wall having a thermal con...
A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked . Kind...
Q: An arbitrary material has an elastic modulus of 118 GPa. How much tensile force was applied to a 100...
A:
Q: Rank the curves based on the change in strain that occurs during the necking phase. Rank the curves ...
A: Various stages shown on the stress-strain diagram are: Proportionality limit Plastic limit Necking ...
Q: A 0.50-m3 tank contains saturated steam at 300 kPa and constant volume. Heat is transferred until th...
A: Write the given data. V=0.50 m3P1=300 kPaP2=100 kPa
Q: 4.78. Demonstrate that the system modes are orthogonal with respect to the [M] and [K] matrices for ...
A: For solution refer below images.
Q: ulate the reactions at the point O
A:
Q: Q6: Calculate the distance travelled by a bike between three places: 1- It was driven from rest at t...
A: Given Time, t1 = 60 sec t2 = 15 × 60 sec Acceleration, a1 =...
Q: 41 КРа 4X КРа 27 КРа 2Z kPa D 350 А 8Y KPa 450 88 КРа B E For the state of stress as shown in Figure...
A:
Q: The 800 lb load is being hoisted at a constant speed using the motor M, which has a weight of 90 lb....
A:
Q: 4- When the car is slowing down, that means it is a) accelerating b) decelerating 5- We can say that...
A:
Q: Sketch the power density distribution for oxyfuel gas welding and GMAW process.
A: Oxy-fuel gas welding also known as gas welding is a welding process that is based on the combustion ...
Q: he rear window of an automobile is defogged by passing warm air over its inner surface. If the warm ...
A: The heat flux through the window pane can be calculated using the formula given below as-
Q: acceleration occurs within a time interval of 2 s.
A: find the magnitude and direction of acceleration of block B
Q: . For an 8-ft length of gate in the figure, find the compression in strut CD due to water pressure B...
A:
Q: etermine the rate of heat loss per unit length (q′), in W/m, and outer surface temperature Ts,2, in ...
A: Given: A cylindrical pipe of unit length,Ts1=800 Kr1=0.06 mr2=0.12 mT∞=25o C or 298 Kh∞=25 W/m2 Kε=0...
Q: Q7: for the figure shown below, calculate the reactions at the point O 30 15 kN-m 3 kN A B C 1.4 kN ...
A: It is required to determine the support reaction at O
Q: calculate the speed (rpm)
A: calculate the speed (rpm)
Q: A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high. The entire ...
A: Given Mass, m = 3000kg Force, F = 15kN Find Acceleration, a
Q: B: The plate shown below is affected by the forces FA and FB, by assuming the value of 0, calculate ...
A:
Q: Draw the shear force diagram and bending moment diagram using differential relationship between load...
A: Given; uniform distributed load for distance a from open end of the cantilever=q Then point load in ...
Q: Technician A says that a micrometer can be used tomeasure the outside diameter of something. Technic...
A: Micrometers exist in a variety of forms, depending on what they're used for. An exterior micromet...
Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of ...
A:
Q: 8.12 At a certain point in a piece of material there are two planes at right angles to one another o...
A: Find the required values.
Q: B: The plate shown below is affected by the forces Fa and FB, by assuming the value of 0 calculate t...
A:
Q: To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity durin...
A: Solution: Given Data: ks=40 W/m-KDi,1=150 mmti=to=20 mmDi,2=250 mmkp=0.03 W/m-KTp,max=70oCT∞,o=-5oCh...
Q: flour mill has been required to install particulate control equipment to remove 90% of its emissions...
A: From given table- Size range μm mass percent in size range 0-2 10 2-10 20 10-20 20 20...
A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high the entire mass is 3000kg and encountered an unbalanced force of 15 kN.
Estimate the angle of spill in degrees
Step by step
Solved in 3 steps with 2 images
- A full rectangular tank is 3.1m wide, 5.6m long, and 1.9 deep contains fluid weighting 663kN. Find the following: mass of the fluid kgA wooden barge of rectangular cross-section is 8 m wide, 4 m high, and 16 m long. It is transporting in seawater (s 1.03) a total load of 1,500 kN including its own weight and cargo. If a weight of 75 kN (Included in the 1,500-kN) is shifted a distance of 2.5 m to one side, it will cause the barge to go down 450 mm in the wdge of immersion and also rise 450 mm in the corresponding wedge of emersion The barge floats vertically (on an even keel) before the shifting of the weight. Compute how far above the waterline is the center of gravity of the loaded barge. W = 1500 kN 4, D D/2 BF 8 m 25m 60 kN/m 75 kN 1425 k 0.45 4 m Bo o BF 3.42 m•:) A SPHE RICAL BALLoON IS FILLED WITH HELIUM to A MAXIMUM DIAMETER OF 3¢4 AT A 6AGE PRESSURE OF 8.18 in Ha and 28 TEMPERATURE - FIND THE MASS OF THE HELIVM loNTA INED INSIDE THE BALLOON.
- Problem 2: An ice cube floats in a glass of water. What fraction of the ice cube lies above the surface of the water? Assume the density of water and ice are 1000 kg/m3 and 920 kg/m3, respectively. m2 A qubo material is submorsod 9 w thA door in the side of a tank is 3.1 m wide and 5.7 m high the tank is filled with oil of relative density 0.78 to a position 1m above the top of the door. What is the line of action of the force from the surface in meters.Q1/ A piston pushes down on a volume of hydraulic oil ISO 68, trapped in a cylinder, its bore is 10cm, and the height of the unstressed column of oil is 50cm. The oil has a bulk modulus B=2.2 *105 psi. When a force of 2500N is applied to the piston. How much does the piston displace? Note : (The ISO 68 has a density of 54.9 Ib/ft(880 kg/m³)
- Answer the following. A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to decrease by (0.08) percent. What is the bulk modulus of elasticity of the liquid? B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated about its central axis at (60 r.p.m). How much liquid is spill and how deep of the water at the central axis.Two capillary tubes with 4mm and 2mm inside diameters were inserted into a liquid of density 1.12gcm^-3. Calculate the surface tension of the liquid if the difference between the capillary rises in the tubes is 2cm. Assume contact angle Is zero.1A square boat of area = 2 m2 floats on the water with 1 m of boat submerged in the water. Estimate the buoyant force on the boat and the pressure at the bottom of the boat. The density of water is 997 kg/m3. Fb = 30,000 N and P = 20,000 Pa Fb = 10,000 N and P = 20,000 Pa Fb = 100 N and P = 200 Pa Fb = 20,000 N and P = 10,000 Pa 2Explain the basic functioning of a hydraulic lift. Be sure to include the terms pressure, density, and buoyant force in your explanation. Give one example of a hydraulic lift you have encountered. 3A common practice when parenting is to take a jar of baby food and place it into hot water to heat the food up. Describe this process in terms of heat transfer. Be sure to include the terms specific heat capacity, hot, cold, transfer, and thermal equilibrium. professor can you answer these questions please?
- A 25 m high vertical column of a fluid of density 1800 kg/m³ exists in a place where g= 9.6 m/s?. What is the pressure at the base of the column in kPa?A commpon way of salvaging cannons from old wreacks is to attach an inflatable balloon filed with air. Assume that the cannon is a solid cylinder of iron which is 1.30m long with a radius 17.3cm. The density of iron is 7.87g/cm^3. a. If an air bag were filled twice the volume necessary, what will be the tension in the rope between the air bag and the cannon when the air bag reaches the surface and comes to rest? What volume of air bag wil be floating above the water surface?A vat contains a mixture of oil and water. The water forms a lower layer which is 0.8 m deep, and above it there is an oil layer 0.3 m thick. The density of water is 1000 kg/m², and the density of oil is 800 kg/m?. Find the force on a flat door at the bottom of the vessel that has a cross-sectional area of 0.5 m?. The acceleration due to gravity is 9.81 m/s. Oil, P. = 800 kg/m3 h. = 0.3 m Water, Pw = 1000 kg/m3 h= 0.8 m A = 0.5 m² O a. 1.28 kN оБ. 4.32 kN O c. 10.2 kN O d. 5.4 kN e. 5.1 kN