T/2 A 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member CD. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm

T/2 A 1200 Nm A homogeneous steel shaft (G=83GPA) is loaded as shown in the above Figure. Assuming T = 300 N-m, determine the torsional force in N-m in Member CD. Note: Include sign (+/-), assuming the direction of Torsion (T) at D is positive Given: AB: Length = 1.75m, Diameter = 75mm BC: Length = 1.50m, Diameter = 60mm AB: Length = 1.00m, Diameter = 40mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A steel strip of length L = 200 mm is fixed at A and rest at B on a vertical spring of stiffness k = 2N/mm. The steel strip is 5 mm wide and 10 mm thick. A vertical load P = 50 N is applied at B as shown. Consider E = 200 GPa, the force (in N) developed in the spring is A L P B K
Figure below shows a uniformly tapering bar of rectangular cross-section of length L and thickness t. The width of the bar at one end is b₁ and the width at the other end is b2, where (b₂> b₁). The bar is subjected to an axial force P. The axial deformation due to load P is given by _mm. b₂ PL atE b₁ = 20 mm b₂-40 mm -In () then the value of (a + c) is
Determine the stiffness matrix of the given system and obtain the condensed stiffness matrix at the dynamic DOFs if the dynamic forces applied in-plane translational DOFs. All members are axially rigid. E=30000 MPa; I=8x10⁹ mm4; L= 4000 m. Hint: Evaluate the stiffness matrix applying the unit deformation metod as given example in the figure!!! m m m U3 U₂ U₁ mm. u₁=1 and urest=0 U4 U3 2m) U₂ EI, L (2m) U₁ 2EI, L
strength of materials
Solve the problem below and show your complete, systematic and neat solution with explanation.
Mechanics of Deformable Bodies 6 in. in.- 5 in. 4 in. A steel tube with the cross section shown carries a torque T. The tube is 6ft and has a constant wall thickness of 3/8in. (a)Compute the torsional stiffness k=TTO of the tube. (b) If the tube is twisted through 0.5°, determine the shear stress in the wall of the tube. Use G=12x 106psi.
50 MPа A 35 MPa B 30 90 MPa The state of stress at a point in a member is shown on the element. You are required to determine the normal stress and shear stress acting on the inclined plane AB and show the result on the sectioned element: b. Using the stress transformation equations. NOTE: support your answer with sketches and the FBD.
The cantilever beam shown is an aluminum pipe that has an outside diameter of 114 mm and an inside diameter of 97.3 mm. A moment of 3 kN-m is applied at the free end. Find the rotation at the free end of the pipe. Neglect the weight of the pipe. М 33KN.m 2m Mod. of Mod. of Coeff, of Elasticity Rigidity G Thermal Ultimate Strength Density kg /m3 x 10 Tensile Yield Strength F, MPa Expansion a m/m/C x 10-6 Poisson's MPa MPa MPa Ratio Material x 10 x 10 Tens. Comp. Shear Steel ASTM A36 or A501 7.85 207 83 250 400 11.7 0.25 Steel (high-strength low-alloy) ASTM A992 7.85 207 83 345 450 11.7 0.25 Steel AISI 1020 hot-rolled 7.85 207 79.3 210 380 11.7 0.25 Steel AISI 1040 hot-rolled 7.85 207 79.3 290 520 11.7 0.25 Stainless steel 7.85 200 80 280 580 410 11.7 0.25 (annealed) Cast iron (gray) 7.21 103 41 140 550 220 10.6 0.26 Aluminum allov 2.64 70 28 240 260 190 23.6 0.33 6061-T6 Magnesium alloy 1.794 45 17 210 280 140 26.1 0.34 Titanium alloy 4.40 114 45 900 970 690 9.7 Nominal Outside Inside…
A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P = 7 kN, Determine the axial deformation of uniform bar 1 (in mm). Indicate negative sign if compression. 5P E-110 GPa 3P E=200 GPa 7m 3M 80mm 30 mm 30 mm 80 mm 30 mm 30 mm
The beam section given in the figure is under the influence of M = 5 kN.m bending moment. Section C and B ' Calculate the normal stresses that will occur at the points. E = 200 GPa. (N-A axis weight passes through the center.)