An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R = 20 mm as shown in the figure. The length I of the member is 3 m. MT R Ri If a G1 = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in the tube. Select the correct response 77T

An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R = 20 mm as shown in the figure. The length I of the member is 3 m. MT R Ri If a G1 = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in the tube. Select the correct response 77T

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Part 2,3,4
The stepped steel shaft carries the torque T. Determine the maximum allowable magnitude of T if the working stress is 12 MPa and the rotation of the free end is limited to 4°. Use G = 83 GPa for steel. T 80 inm 60 mm 4 m 3 m
A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
The rigid bar ABCD of negligible weight is initially horizontal, and thesteel rods attached at A and C are stress-free. The 20-kip load is thenapplied and the temperature of the steel rods is changed by ΔT. Find ΔTfor which the stresses in the two steel rods will be equal. Use α=6.5x10-6/oF and E=29x106
A rigid bar ABCD is supported by two bars as shown in the figure. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in rod (1) is -1350 µm/m. Determine the normal strain in rod (2) if there is a 1-mm gap in the connection at pin C before the load is applied. A 240 mm B (1) O 1281 um/m O 1877 µm/m O 1141 µm/m O 1358 µm/m O 999 µm/m 360 mm (2) Rigid bar 900 mm C 140 mm, 1,500 mm
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
At a temperature of 34°F, a 0.06 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a = 12.5 x 10-6/°F] and bar (2) is stainless steel [a = 7.3 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 33m B (2) Answer: Final temperature = 55 in. -0.06. gap °F.
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…
Problem 3: Inside a steel tube, 2.4 meters long, 34 mm radius, and 1.5 mm thick, 32.5A circular bar made of aluminum with a radius of mm is inserted and these two materials arethey are linked together to form a cross section that will work. This cantilever beam obtained from end Ait is fixedly supported. This cantilever beam,A torque of T = 900 Nm from end B(torque) is applied. Stiffness modulus of steel, Strength= 77 GPa and the stiffness modulus of aluminum Gal = 26Since GPa is the rotation at point BWhat is the (torsion) angle? Calculate.
The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for the aluminum, 83 GPa for steel and 35 GPa for bronze. Aluminum 100 mm -3 m- 4 kN.m Steel 75 mm -2 m 1.5 kN - m Bronze |--15m-l
A magnesium-alloy rod (E = 6.5 x 10 ksi) of Prob. 3.4-6. diameter d 1 in. is encased by a brass tube (E 15 x 10 ksi) with outer diameter d. = 1.5 in.; both have length. L = 20 in. An axial load P = 10 kips is applied to the resulting bimetallic rod. (a) Determine the normal stresses and , in each material, assuming that the magnesium rod and brass tube are securely bonded to each other. (b) Determine the elongation of the bimetallic rod. P