T1 and T2 in brass rod in thermal conductivity test are located in direction that Select one: a. T2 on the heating side and T1 on the cooling side b. T1 and T2 are both on the cooling side c. T1 and T2 are both on the heating side d. T1 on the heating side and T2 on the cooling side

Q: 1. A cylindrical container gromm in diameter, 2 meters long is to be filled with methane gas, 16°C.…

A: Dear student,                     According to the guidelines, I am allowed to answer only one…

Q: One cool 5.0°C spring morning, Mason lays a brick sidewalk up to his house, placing the 25.0-cm-long…

A: Given data L0=0.25 mα=10×10-6/°C∆T=36-5°C=31°C

Q: In order for a certain refrigerator door to close tightly, the refrigerator must beleveled up 0.24…

A: Given data as per question Total thickness = 0.24 in The thickness of lower shim =0.097 in

Q: informations of thermal system

A: Thermal system s

Q: A 4.8 m long from fixed point, 0.5 m wide and assumed a thickness of 30 mm throughout a springboard…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: ylindrical rods can also be treated as being infinitely long when finding temperatures near the…

A: so we have to determine if it is appropriate to use cylindrical rod as as infinite long when we need…

Q: informations of Thermal system

A: Thermal systems are those that include the capacity and exchange of heat. Heat stored in a fabric…

Q: Two wires of equal lengths, one Aluminum, and the other steel, were stretched the same amount under…

A:

Q: why bare pipe has 0% efficiency and full covered insulate pipe has more efficiency

A: A thermal insulator has a low thermal conductivity and is a poor heat conductor. To reduce heat loss…

Q: A seesaw that weights 45lbs and its 5m long is balanced on the fulcrum in the center.  1- Two…

A:

Q: There is no difference between the words BENT and FLEX

A: The word BENT is related to the Bending that occurs in machine parts  and  The Word FLEX is related…

Q: Discuss the difference between static and dynamic temperatures.

A: difference between static and dynamic temperature

Q: Which statement is False with regards to the mechanical behavior of human Blood? a. Formation of…

A: a. Red blood cells contain hemoglobin — an iron-rich protein that gives blood its red color.…

Q: When the heat gain is less than the heat losses, then Select one: a. We will need a cooling system…

A: option 1 is the correct answer. i.e. we need a cooling system we know that energy balance…

Q: Two aluminum posts are located at equal distance from the middle steel post as shown. Take note that…

A: The posts are arranged in the parallel connection. Due to applied external force P, first steel post…

Q: Hot hardness means that the material will lose its hardness at high temperature. True or false and…

A: The hardness of a material is associated with the strength of the material. This is associated with…

Q: The diameter of the bolt is .500 inches. Force

A: given:diameter of the bolt d=0.500inforce F= 750pound

Q: During normalizing process of steel, the specimen is heated a. Between the upper and lower critical…

A: Normalising process: Normalizing is a heat treatment process that is used to make a metal more…

Q: Bar one has a Young's modulus that is bigger than that of bar two. This indicates bar one:

A:

Q: What is Newton law of cooling

A:

Q: Q3): Choose the correct answer for the following: 1. Fine threads bolts have a tensile stress area…

A: Given questions are: 1. Fine thread bolts have a tensile stress are  smaller than coarse thread…

Q: Figure Q2 shows a beam subjected to distributed loading. Knowing the beam is fixed supported at one…

A: a) Free body diagram of the beam The free body diagram of the given beam is where, RB is the…

Q: Vickers Hardness Number (HV) value is inversely proportional to a. Indentation mean diagonal b. All…

A:

Q: Please select all that applies. The possible failure modes for bolted joints are: shear in the bolts…

A: To select: The correct options. Concept used: Failure of the bolted joints: The bolted joints may…

Q: Hooke’s law holds well up to yield point. Select one: True False

A: Yield Point In materials sciences and engineering, the yield point is a stress-strain curve that…

Q: An object which has only mass and no size is called rigid body Select one: True False

A: Rigid body: A body in which particles have not relative motion with each others when we applied any…

Q: Thermosetting plastic materials have the cost saving advantage in that they can be injection molded…

A: Thermosetting plastic materials have the cost-saving advantage in that they can be injection molded…

Q: with a 3. Copper is at 37.8 degrees Celcius initially. It is then cooled off until it reaches a…

A:

Q: The risk of damages in the life of a machine component can be eliminated by using individual…

A: This statement is (TRUE)

Q: A building has three boilers to provide heat. Each boiler has a 150.000 BTU/Hr capacity. On a design…

A: Given:  There are 3 boilers each of capacity 150,000 BTU/hr capacity.  1 boiler Capacity = 150,000…

Q: Write in your own words the actual experimental procedure followed. The procedure should reflect the…

A: The procedure followed in performing the test: Step 1: A clean specimen is to be taken with all the…

Q: PMM1 means, the machine does not follow the second law of thermodynamics Select one: True False

A: False

Q: What type of thermocouple used to measure 1500 C and more temperature ranges? O a. Platinum-Rhodium…

A: Correct Option: a.) Platinum-Rhodium Type T/C.

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: Find the force in member EC? 30% 6 ft B 300 lb 6 ft 300 lb 30° -6 ft

A: A plane truss given

Q: During the selection of material, the characteristics of the material are an important factorcompare…

A: Answer is( TRUE)

Q: Compute for the value of the uniformity coefficient with the data shown below. D10 = 0.08 mm…

A: UNIFORMITY CO-EFFICIENT: It is defined as the ratio of size of opening that will just pass 60% of…

Q: :Measurement of vibration is required to

A: GIVEN DATA A MCQ GIVEN ASKING VIBRATION MEASUREMENT REQUIRED TO WE HAVE TO CHOOSE CORRECT OPTION

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.