QUESTION 1A hydraulic clutch of a motor car works as follows: A foot pedal with a mechanicaladvantage of 2,5:1 acts on the master cylinder which is 15 mm in diameter. Hydraulicfluid is displaced to the slave cylinder which is 20 mm in diameter. The force from theslave cylinder on the clutch is 850 N and the foot pedal moves 70 mm when pressedin.1.1 Determine the force which must be applied to the foot pedal.1.2Determine the distance that the slave cylinder will move if the foot is depressedfully.1.3 Assume 2% air (per volume) is present in the system which contains 100 mlfluid. Assume the bulk modulus K of the fluid is 1,8 GPa.

Name: QUESTION 1A hydraulic clutch of a motor car works as follows: A foot
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: QUESTION 1A hydraulic clutch of a motor car works as follows: A foot pedal with a mechanicaladvantage of 2,5:1 acts on the master cylinder which is 15 mm in diameter. Hydraulicfluid is displaced to the slave cylinder which is 20 mm in diameter. The

2,5:1Dm=15mmDs=20mmFs=850NFoot pedal moves=70mm To-Find:- a Force applied to the foot pedalb…

Engineering

Mechanical Engineering

fluid is displaced to the slave cylinder which is 20 mm in diame slave cylinder on the clutch is 850 N and the foot pedal moves in. 1.1 Determine the force which must be applied to the foot ped 1.2 Determine the distance that the slave cylinder will move if fully.

fluid is displaced to the slave cylinder which is 20 mm in diame slave cylinder on the clutch is 850 N and the foot pedal moves in. 1.1 Determine the force which must be applied to the foot ped 1.2 Determine the distance that the slave cylinder will move if fully.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A load of 200 pounds is exerted on a piston confining oil in a circular cylinder with an inside diameter of 2.50 inches. Compute the pressure in the oil at the piston.
The flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 62.4 lb/ft. 4ft 8 ft Enter the exact answer. F = lb exact number, no tolerance
Draw the FBD of block A, block B, and blocks A and B
A plane moves at 820km/h as it makes a horizontal circular turn of radius 15.0 km. a. Draw a free body diagram and show all the forces on the pilot man who is inside the plane. b. Figure out the magnitude of the net force on the 78.0kg pilot. 10000
1. A hydraulic lift system utilizes two 3 in. diameter cylinders. Workers must determine how much the system is capable of lifting before deciding how much weight can be lifted safely. The system runs at 2000 lb/in². What is the area of each piston? How much is the system capable of lifting?
Urgent 3D model design for this vehicle body (4 passengers / 4 chairs if possible)
Determine the direction the force was applied by the fireman on the fire hydrant nozzle while using it?
Item #1 | Directions: Answer the following. Kindly answer the given questions completely and correctly. Any missing answer will result in DISLIKING your solutions. 1. A uniform bar 20 ft long and weighing 20 lbs is held by Peter 2 ft from the left end while John carries the same bar 5 ft from the right end. a. Draw the clear and neat figure of the system indicating the center of gravity of the uniform bar. b. Draw the force diagram and reflect the distances between the forces. c. Establish the equations for the two conditions of equilibrium.
A hydraulic press is used to raise an 80 - kN cargo truck. If oil of sp. gr. 0.82 acts on the piston under a pressure of 10 MPa, what diameter of piston is required?
In a hydraulic press the large piston has a cross sectional area A1=200 sq. cm and the small piston has a cross sectional area A2=5 sq. cm. If the force is 250 N to the small piston. Compute the force acting on the large piston. a. 10 kN b. 12 kN c. 21 kN d. 20 kN
TRUE OR FALSE. SHOW SOLUTION. 47 lb-in is equivalent to 4.31 N-m.
convert to correct unit