T = 310 KThe thickness of a wall is 0.07 m. right side of the wall8.air and300 Kexposed to the ambient air. External surface temperature of thesurwall (right side) 500 K and heat transfer coefficient h=3OW /m² Kk=0,86 W/mKemissivityrate of 0.78 and heat transfer coefficient of the wallWhat isthe temperature of the inner wall?

given data; ⇒thickness of wall (x)=0.07m⇒external surface temperature of wall right side…

Answered: T. = 310 K The thickness of a wall is…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.18P

See similar textbooks

Similar questions

An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.
2.7 A very thin silicon chip is bonded to a 6-mm thick aluminum substrate by a 0.02-mm thick epoxy glue. Both surfaces of this chip-aluminum system are cooled by air at , where the convective heat transfer coefficient of air flow is . If the heat dissipation per unit area from the chip is under steady-state conditions, draw the thermal circuit for the system and determine the operating temperature of the chip.
The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
The heat transfer coefficient for a gas flowing over a thin float plate 3-m long and 0.3-m wide varies with distance from the leading edge according to hc(x)=10x1/4Wm2K If the plate temperature is 170C and the gas temperature is 30C, calculate (a) the average heat transfer coefficient, (b) the rate of heat transfer between the plate and the gas, and (c) the local heat flux 2 m from the leading edge. Problem 1.18
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
The heat transfer rate from hot air by convection at 100C flowing over one side of a flat plate with dimensions 0.1m0.5m is determined to be 125 W when the surface of the plate is kept at 30C. What is the average convection heat transfer coefficient between the plate and the air?
The air-conditioning system in a Chevrolet van for use in desert climates is to be sized. The system is to maintain an interior temperature of 20C when the van travels at 100 km/h through dry air at 30C at night. If the top of the van is idealized as a flat plate 6 m long and 2 m wide and the sides as flat plates 3 m tall and 6 m long, estimate the rate at which heat must be removed from the interior to maintain the specified
Determine the rate of heat transfer per meter length from a 5-cm-OD pipe at 150C placed eccentrically within a larger cylinder of 85 magnesia wool as shown in the sketch. The outside diameter of the larger cylinder is 15 cm and the surface temperature is 50C.
Q1-A block as sphere made of Teflon initially at a temperature of 90 C is suddenly immersed in a fluid at 20 C. The convection heat- transfer coefficient is 15 W/m2 C. Determine the dimension of the block that it is just considered as lumped-capacity system. Calculate : (1) the time the center of the sphere reaches the half value of initial temperature and, (2) the heat loss from the block at that time.
Consider a rectangular warehouse with the dimensions of 40m long x 20m widex10m height. The overall heat transfer coefficient for all sidewalls is Uwall=0.3 W/m2K (Approx. R=20 hr.ft2.oF/Btu) and for the flat roof, it is Uroof= 0.20W/m2K. The floor can be assumed to be insulated and we can ignore the heat transfer through the doors, etc. We want to maintain the inside air temperature at 15oC while the outside temperature is 0oC by using a thin-walled, 5.0cm diameter copper pipe that carries steam. Steam enters the pipe as saturated vapor at 100oC. So, as it starts losing heat to the inside air, it starts to condense. The thin-walled pipe is made of, a highly conductive material such that the outside temperature of the pipe is at 100oC steam temperature over its entire surface. The average emissivity of the pipe is 0.8 and the only radiative exchange is with the air inside of the building at 15oC. We want to determine the length of the pipe necessary to keep the inside temperature at…
Plate glass 5 mm thick at200°C is to be cooled fromb bothsides using air at 40°C. Ifs surfacecracks are to bea avoided determine them maximumvalue of convective heat transfer coefficient. Material properties are density = 2500 kg/m3, = specific heat 670 J/kgK. Thermal conductivity 0.744 W/mk. Also determine the time required in this to cool the plate to 80°C.
Convection - Heat Transfer Coefficient (HTC) (1) The temperature of inner surface of insulation wall is t,=100°C, while the outer surface releases the heat by convection to surroundings air with temperature of -20°C. The thickness of the insulating layer is 5 cm and its thermal conductivity of 0,05 W/(m-K). What is the value of heat transfer coefficient on the outside this wall if its surface temperature t, is of 0°C.

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning