A pin fin (L= 38 mm , d = 3.0 mm) attached to a hot surface, Ts = 159°C with a convection heat transfer coefficient is (35.2= W/m K) and surrounding air at 23°C, if the fin efficiency is 0.75. What is the actual heat transfer from the fin (W)? Select one

A pin fin (L= 38 mm , d = 3.0 mm) attached to a hot surface, Ts = 159°C with a convection heat transfer coefficient is (35.2= W/m K) and surrounding air at 23°C, if the fin efficiency is 0.75. What is the actual heat transfer from the fin (W)? Select one

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
There is a 1.20-cm-thick stagnant air pocket. A) What thickness of cork would have the same R-factor as the stagnant air pocket? The thermal conductivity of air is 0.0230 W/m·K and of cork is 0.0460 W/m·K.in cm B) What thickness of tin would be required for the same R-factor as a 1.20-cm-thick stagnant air pocket? The thermal conductivity of air is 0.0230 W/m·K and of tin is 66.8 W/m·K . in m i asked how to do this but got the wrong soloution
Q2/ A plane wall (K =17 W/m.°C ) with (60 mm) thick. Both sides of the wall are insulated with ( 2 cm) layer of insulating material having (K=0.22 W/m.°C ) The heat transfer coefficient, considering convection on both sides of wall are ( 120 and 10 W/m.°C ) respectively. Calculate the heat transfer per unit area if the temperature difference across the wall is (90 °C).
Q2) A short fin is attached to a flat surface temperature T = 40 °C. Determine the fin temperature at 5 cm from the base and the rate of heat loss from the entire fin. Considering that the ambient air temperature Too = 20 °C, convection coefficient h = 50 w/m².°C, fin conduction coefficient k = 300 W/m.°C, fin dimensions (L = 7cm, W = 5cm, t = 2mm), Perimeter, P = 10 cm. 612223 T=40 °C X = 5 cm L = 7 cm h=50 Too=20 k-300 W = 5 cm = 2mm
I need the answer as soon as possible
Please quick answer
You are designing a 3m x 3m floor with radiant heating. The floor has 12 parallel pex pipes (k = 40 W/mK) of L = 3m, OD = 25mm and ID = 20mm. Hot water (TInfintiy 1 = 90oC, h = 200 W/m2K) runs through the pipes continuously. The surface below the pipes is perfectly insulated. Above the pipes, there is a 3mm layer of bonding material (? = 12 W/mK) and a 9mm layer of tile (k = 2 W/mK). Above the tile, there is air (TInfinity 2 = 25oC, h = 20 W/m2K). Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), Hint: Assume that the “layer” of pipe starts at the center point (e.g. for conduction purposes, the pipe is OD divided by 2 thick). For convection, consider the entire pipe surface. a) What is the total heat rate entering the room above the floor? b) What is the temperature of the top of the tile?
A square pin fin (w=0.6 mm, L=33 mm) is attached to hot surface [87 mm * 69 mm] Ts= 172°C with convection heat transfer coefficient of (1383 W/m K) and surrounding air at 24°C, if the fin efficiency is 0.81 and the center to center distance between any two successive fins =1.5 mm. What is the heat transfer rate (W) from the base surface ONLY when the fins are attached to it?
The outer surface of an oil heater at a uniform temperature of 100°C is to be filled with straight rectangular fins having a uniform thermal conductivity of 180 W/m.K. The ambient air temperature is 25°C and the heat transfer coefficient is 100 W/m².K. The fin thickness t-1mm, width w= 1m and its length is L= 10mm. If the heat transfer from the tip of the fin by convection, calculate fin efficiency and effectiveness. Tь =100 с Too = 25°C h = 100 W/m2-K L = 10 mm Air k= 180 W/m-K t = 1 mm
S is 6. A spherical shaped vessel of 1.4 m outer diameter is 90 mm thick. Find the rate of heat leakage, if the temperature difference between the inner and outer surfaces is 220°C. Thermal conductivity of the material of the sphere is 0.083 W/mK. (a) 0.2 kW (c) 1.088 kW (b) 0.5 kW (d) 1.6 kW
One vessel having a carbon-steel wall of thickness 5 mm carrying saturated steam and water at 423K. The vessel is insulated with magnesia of thickness 50 mm. If the ambient air temperature is 321 K, determine the heat loss from the vessel. Given: i. thermal conductivity of carbon steel is 52 W/m.K ii. thermal conductivity of magnesia is 0.5 W/m.K iii. surface coefficient of insulation surface is 3 W/m2.K