symmetrical 3 – phase, 3 – wire, 440 – V system supplies an unbalanced Y – connected load of impedances ?? = 5 ∠ 300 Ω ; ?? = 10 ∠ 450 Ω ; ?? = 10 ∠ 600 Ω. Phase sequence is ? → ? → ?. Calculate in the rectangular complex form the symmetrical components of the currents in the R – line

symmetrical 3 – phase, 3 – wire, 440 – V system supplies an unbalanced Y – connected load of impedances ?? = 5 ∠ 300 Ω ; ?? = 10 ∠ 450 Ω ; ?? = 10 ∠ 600 Ω. Phase sequence is ? → ? → ?. Calculate in the rectangular complex form the symmetrical components of the currents in the R – line

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.29MCQ

See similar textbooks

Similar questions

Figure Q2 (a) shows the spacing of a double circuit 3-phase overhead line. The phase sequence is RYB and the line is completely transposed. i) Critically assess the significance of transposition in a 3-phase overhead line. ii) Calculate the inductance per phase for 500 meter length of line using Table 2(a) data for the Figure Q2(a). Table 2(a) GMR of the line Distance a-b' 0.01m 6.6m Distance a-a' 8.5m Figure Q2(a)
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
please solve for nodal stress method. (if it is possible to apply supernodes)
What are FACTS (Flexible Alternating Current Transmission Systems) devices, and how do they enhance the control and stability of power systems?
For transferring electrical power at 220 kV, six conductors of ACSR Drake constitute a 60Hz double circuit three phase line arranged as shown below. The vertical spacing between consecutive conductors is 14ft; the longer horizontal distance is 32ft whereas the shorter horizontal distance is 25ft. a. Find the inductance per phase per mile and the inductive reactance per phase in ohms per mile. b. Find the capacitive reactance to neutral in ohm-miles. c. Find the resistance per phase per mile in ohms per miles. d. If the length of the line is 90 miles then draw an equivalent circuit of the line and analyse the open circuit and short circuit performance of the line. e. Find the maximum power we can transmit over the line. f. If the line is delivering power to a load of 20MW at 0.8 power factor lagging then find the voltage at the receiving end of the line. Also, Determine the voltage regulation, losses and efficiency of the line. g. If a fixed shunt compensation of 3 MVAr is attached at…
Problem 3.5: From a 3-phase, 480 V generator switchboard, a feeder takes 3-phase power to two equipment at the other end via cable and trans- former with the combined series impedance Z = 0.04 + j 0.09 Q per phase. The voltage at receiving end point A rises and falls as a large 3-phase, 500 kVA load at point A varies over time. The small 1 kVA load, also connected at point A, remains online continuously, and must accommodate the voltage variations at point A with the 500 kVA load fully on or fully off. Determine the voltage range that the 1 kVA load will see, over which it must perform within its specifications.
A three phase symmetrical double circuit line is arranged in a horizontal plane as shown in figure below. Calculate and derive an expression for the transposed line for the inductance. Assume balanced equally distributed loads.
Discuss why a. Complex power in an AC circuit is more than the DC resistance. b. Receiving end voltage of an unloaded long line may be more than sending end voltage. c. Inductance of the three phase of a transmission line are generally not equal. d. It is necessary to use the geometric means radius in the formula for the inductance calculation whereas the formula for the capacitance calculation uses the actual radius.
() State TWO (2) advantages of three-phase system over single-phase system. (ii) For a three-phase system with delta load connection, derive line and phase current relationship as stated in equation (2.1). line = V3lpnase 4 – 30 A (2.1)
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
A three-phase, 60-Hz, untransposed transmission line runs in parallel with a telephone line for 20 km. The power line carries a balanced three-phase rms current of Ia = 3202 – 240°A. The line configuration is as shown in figure. Assume zero current flows in the ungrounded telephone wires. Find the magnitude of the voltage induced in the telephone line. = 32020°A, Ī, = 3204–120°A, and a 4 m 4 m 5 m d G2 mO