Suppose the weight of the drawbridge in the figure below is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? 1/6 7.5 m (b) What is the magnitude in newtons and direction of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2,625 kg. N magnitude direction up Additional Materials Reading 40°

Suppose the weight of the drawbridge in the figure below is supported entirely by its hinges and the opposite shore, so that its cables are slack. (a) What fraction of the weight is supported by the opposite shore if the point of support is directly beneath the cable attachments? 1/6 7.5 m (b) What is the magnitude in newtons and direction of the force the hinges exert on the bridge under these circumstances? The mass of the bridge is 2,625 kg. N magnitude direction up Additional Materials Reading 40°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor. Thank you. This part features some concave arcs that are equally spaced. There are some larger arcs (.072 radius) spaced _____ degrees apart and some smaller arcs (.030 radius) spaced _____degrees apart. (Multiple Choice)a. 22.5 (22°30′); 22.5 (22°30′)b. 12.5 (12°30′); 11.25 (11°15′)c. 20.5 (20°30′); 10.25 (10°15′)d. 22.5 (22°30′); 11.25 (11°15′) What type of section is shown in Section B? (Multiple Choice)a. Offsetb. Fullc. Halfd. revolved Section B uses a center line between the left half and the right half. Is this recommended practice? (Multiple Choice)a. yesb. no
The answer should be 24,6kN when rounded up.
I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal places for magnitude. DO NOT FORGET YOUR UNITS. Enclose all final answers in a box. No need to copy the question or problem. File submissions should be a single PDF. II. PROBLEM SOLVING 1) Given the figures and data below, solve what is being asked for. Y-axis 200mm -200mm 50mm 50mm 100mm 200mm 100mm Y-axis Yo 200mm 100mm 3°1 100mm 547 - ATT HA LO - CHIR →→X-axis -Xo →X-axis
I need the answer for number 10.
Please answer 3, 4, 5, 6, 8, 9, 10, 12 1 is 0, 2 is 0, 7 is point A, 11 is 2. I included a picture of someone who solved but they were mostly incorrect. Please do not answer if the solution set I provided with the incorrect answers was you. I appreciate the attempt, but the solutions for 3, 4, 5, 6, 8, 9, 10, 12 were marked wrong, so unless you have different answers, please do not submit the same incorrect solution set. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the mass center G is set as the origin (datum), the gravitational…
I need these three parts answered (Multiple Choice). If you can not answer all three parts please leave it for another tutor to answer. Thank you. For the two holes identified as datum D, what is the total size tolerance specified for those holes? (Multiple Choice)a. .002'b. .003'c. .004'd. .006' The two holes identified as datum D have a counterbore on one end. What size toleranceis specified for the counterbore diameter? (Multiple Choice)a. .010″ (±.005″; see title block)b. .020″ (±.010″; see title block)c. .030″ (±.015″; see title block) What letter represents the revision status of this print? (Multiple Choice)ABCD
can you redo D please with the actual answer
f) Answer the question shown in the images. Show every step
Problem-AA: Consider the following system of equations: -123 = 1.5a + 25n 5 = -21a +n Calculate the two unknows.
Solve all 10 questions 1 to 10 1 to 10
5 In micrometer, circular scale is found on the thimble. Select one: True False