Incorrect please resolve both parta

Q: 1-) b. 1+j 1 Evaluate a. 1+j

A: Ans(a)  j2=-1 Divide by 1-j both sides 1-j1+j×1-j1-j (1-j)21-j2=1+j2-2j2=-2j2=-j

Q: 355 coupe for some maintenance check. Before proceeding to your regular maintenance routine, it is…

A: Odd matric number:

Q: v) w) What is the distance, dsy, of shape 5's centroid from axis Yo? What is the distance, dzy, of…

A: (v) Consider the shape 5 and calculate the distance, d5y, of shape 5's  centroid from axis y0.

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Consider a virtual load Q, acting vertically downwards, is applied at point A.Draw the given truss…

Q: how does F_BC equal 6

A:

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: TC Sin2 * cos' z 2. sin? dx

A:

Q: For the pipe section shown in Fig. 8.5 in text (before 180° bend), which includes the entrance (de-…

A: Given:

Q: What is the value of w and y? y W 6V2

A:

Q: Piston and cylinder of a reciprocating steam engine forms a pair

A: A sliding pair is formed when the two pieces of a pair are joined in such a way that one may only…

Q: Forces and moments are scalar Forces are moments are vector quantities.

A: Forces and moments are both physical quantities that can be used to describe the behavior of objects…

Q: Find ex, ey and y. NOTE: ex and ey in mm/mm and y in radians.

A:

Q: S) t) What is the distance, d3x, of shape 3's centroid from axis Xo? What is the distance, d6x, of…

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: The steel box wrench (E=29,000ksi, v=0.32) is loaded with a 40-lb horizontal force and a 25-lb…

A:

Q: complete 1-F on part a and b

A: Given Data: md2xdt2+cdxdt+kx=f(t)m=2 kgc=3 kg/sk=20 N/mf(t)=10 N   To Find: (a) Determine the…

Q: Determine ly and ky.

A:

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: 200 m The spool has a mass of 40 kg and a radius of gyration of k-0.65 m. If the 20 kg weight is…

A:

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: The Answer is cut off on the right side.

A:

Q: 0 = 0° A

A:

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: Z is incorrect

A: