Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap. The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, water that comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tap is 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jet impinging on the sink at three given flow rates.

Q: Water is pumped from a lake through an 8-in. pipe at a rate of 10 ft'/s. If viscous effects are…

A: Given Diameter of the pipe = 8 in = 0.666 ft Flow rate = 10 ft3/s Elevation = 6ft To find Pressure…

Q: A water turbine operating at 85% efficiency is under a head of 100 m. If the constant discharge is…

A:

Q: Water is flowing steadily through a closed pipe system of constant diameter. Station 2 is 1 m higher…

A: Given data: The height of station 2 is, z2 = 1 m. The velocity at station 1 is, v1 = 3 m/s. The…

Q: 2. A pump is used to move water (p = 1000 kg/m³) from a lake into a large tank as shown below. The…

A:

Q: Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C…

A:

Q: A pump is installed to deliver water from a reservoir of surface elevation zero, to another of…

A: The flow rate of water is given by calculating losses by pump and head. Now,

Q: Water is delivered through a horizontal 20-cm-diameter pipe at a flow rate of 0.5 m3/s. If a…

A: Answer: The pitot probe positioned downstream of the manometer would indicate a pressure of 176.65…

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: Since you have asked multiple subparts, only the first three subparts are solved for you. If you…

Q: Consider a duct systems where air flows through two 8 in. by 10 in. ducts that merge into an 18 in.…

A:

Q: A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated…

A:

Q: Water at 60°F is pumped from a reservoir to the top of a mountain through a 6-in. Schedule 120 pipe…

A:

Q: Water is pumped from a lake through an 8-in. pipe at a rate of 10 ft'/s. if viscous effects are…

A: Given conditions; Flow rare = 10 ft^3/sec Viscous effects are negligible Diameter = 8 inch Z2=6ft…

Q: Inlet and throat diameters of a horizontal venturimeter are 350 mm and 150mm respectively. The…

A:

Q: A fan draws 1.42m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm…

A: Given Data ⇒ Discharge of fan (Q)=1.42 m3s Static pressure (P)=2.54 cm of water Diameter of the duct…

Q: The ratio of the mass flow rate, m b,

A: Given; A steady laminar boundary layer is formed over a flat plate   as shown in figure.…

Q: A large pipe with a cross-sectional area of 1.00 sq m descends 5.00 m and narrows to 0.500 sq m,…

A:

Q: A siphon pumps water from a large reservoir to a lower tank that is initially empty. The tank also…

A: The schematic of the pump water system is shown below:

Q: Pipe A, 30 cm in diameter, branches into two pipes B and C. Pipe B is 15 cm in diameter and pipe C…

A: The discharge is not the quantity of the fluid flowing through the pipe per unit time is called the…

Q: Water flows in a new 10cm diameter cast iron pipe with f=0.027 at a velocity of 1m/s. For each pipe…

A:

Q: A pump with an efficiency of 15mm% is used to pump water from a tank (stationary water inside) at…

A:

Q: A jet of water having a velocity of 30 m/s strikes a series of radial curved vanes mounted on a…

A:

Q: Assuming a permanent loss using the pressure drop from the 180 L/min flow rate and taking energy to…

A: Flow rate ,Q = 180 L/min or 0.003 m3/s Time = 24 hours

Q: A pump has a required NPSH of 3.0 m. Assuming that the pump is elevated at 3.5 m above sea level,…

A:

Q: A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated…

A:

Q: A fan draws 1.42 m³ per second of air at a static pressure of 2.54 cm of water through a duct 300 mm…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: As per bartleby guidelines we are allowed to solve 1st 3 subparts of question. Please post remaining…

Q: A large tank discharges water through an orifice of 5 cm diameter at its bottom as shown in Fig.…

A: Given data:-theoretical diameter, dth=5cm=0.05mactual diameter, dact=4.95cm=0.0495mdepth of water,…

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: Given: Velocity of smaller end (V1)=4.3m/sVelocity of larger end (V2)=2.1m/sLength of the conical…

Q: The water circulates throughout the building in a hot water heating system. If the water is pumped…

A: Given that,

Q: The water level in a tank open to the atmosphere is 20 m above the ground. A hose connected to the…

A:

Q: Water flows through a 2.5 cm pipe at115 L/min and o.15 bar pressure. It vents vertically 1 m above…

A: Given data as per question Diameter of pipe =2.5 cm Flow rate =115 L/min =0.115/60 m3/s Vent height…

Q: A 2-in water jet with a velocity of 130 fps strikes a single vane moving in the same direction of…

A: Given: Jet diameter, d = 2 in = 2in1 ft12 in = 16ft Jet Velocity, V=130 fps Vane velocity, u=50 fps…

Q: A 10-hp pump (installed a the ground level) draws water from a well 30 ft below ground level and…

A: Given question belongs to the subject Fluid Mechanics and from the topic Flow through pipes.

Q: Problem 1 A jet of water discharges into an open tank, and water leaves the tank through an orifice…

A:

Q: A conical tube is fixed vertically with its smaller end upwards and it forms a part of the pipeline.…

A: Given: D1 = 245 mm D2 = 467 mm L = 1.8 m Q˙= 128 litres/s = 0.128 m3/s

Q: A fan when driven by a 5.8 Hp motor at a speed of 800 rpm delivers 510 m3/min at a total pressure of…

A:

Q: The reservoir tank shown contains fresh water air pressurized to 200 kPa. There is a loss of 3.3…

A:

Q: 4. The discharge pipe of a pump is 400 mm in diameter delivers 0.5 m3/sec of water to a building…

A:

Q: A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated…

A: Given data as per question Pipe inside diameter =3 in Flow rate =150 gal/min  The overall efficiency…

Q: A jet of water with a velocity of 30 m/s impinges on a series of canes moving at 12 m/s at 30 to the…

A:

Q: PROBLEM 02: Water entering a pump through an 200mm diameter pipe at 27.6 kPa has a flow rate of 0.1…

A:

Q: Water from an open reservoir A at 8m elevation is drawn by a motor-driven pump to an open reservoir…

A:

Q: 5. Elevation = 100 ft Di = 1 ft (1) e, = 1000 ft %3D D2 = 1 ft lz = 500 ft B Elevation = %3D 20 ft…

A:

Q: a fan draws 1.42m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm…

A: Determine the static head by using the below expression. Here γw is the specific weight of water,…

Q: QUESTION 3 A Pelton wheel with a needle-controlled nozzle develops 1 050 kW against a gross head of…

A:

Q: Pitot-Static Tube Example A pitot-static tube is used to measure the air flow at the center of a…

A:

Q: A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.