Suppose that the temperature at C, tc, can be modeled by Oo + Oita + OztB where ta, tB are the temperature at A and B respectively, and 0,01, 02 are parameters to be determined. Find the parameters 60, 01, 02 that best fit the following data ta tB tc 15 17 14 10 11 9. 12 13 11 18 22 16 20 25 19

Suppose that the temperature at C, tc, can be modeled by Oo + Oita + OztB where ta, tB are the temperature at A and B respectively, and 0,01, 02 are parameters to be determined. Find the parameters 60, 01, 02 that best fit the following data ta tB tc 15 17 14 10 11 9. 12 13 11 18 22 16 20 25 19

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the Fig. 2 below, let Ki = K2 = K and ti = t=t. %3D T -T X Fig. 2 (a) Let T= 0 °C and T= 200 °C. Solve for T: and unknown rates of heat flow in term of k and t. MEC_AMO_TEM_035_02 Page 2 of 11 Finite Element Analysis (MECH 0016.1) – Spring - 2021 -Assignment 2-QP (b) Let T- 400 °C and let fs have the prescribed value f. What are the unknowns? Solve for them in term of K, t, and f.
The stress profile shown below is applied to six different biological materials: Log Time (s] The mechanical behavior of each of the materials can be modeled as a Voigt body. In response to o,= 20 Pa applied to each of the six materials, the following responses are obtained: 2 of Maferial 6 Material 5 0.12 0.10 Material 4 0.08 Material 3 0.06 0.04 Material 2 0.02 Material 1 (a) Which of the materials has the highest Young's Modulus (E)? Why? Log Time (s) (b) Using strain value of 0.06, estimate the coefficient of viscosity (n) for Material 6. Stress (kPa) Strain
state and validate Hooke’s Law and verify the relationship between F and x fo the given data. THANK YOU SO MUCCH!
Q(2) Complete the blank cells in the following table of properties of steam. In the last column describe the condition of steam as compressed liquid, saturated mixture, superheated vapor, or insufficient information; and, if applicable, give the quality. Р (кра) T ('C) v, m'/kg u, KJ/Kg Phase description 300 35 130.24 313.22 135 600 1.34139 275 0.500 600 3090
The viscous torque T produced on a disc rotating in a liquid depends upon the characteristic dimension D, the rotational speed N, the density pand the dynamic viscosity u. a) Show that there are two non-dimensional parameters written as: T and a, PND? b) In order to predict the torque on a disc of 0.5 m of diameter which rotates in oil at 200 rpm, a model is made to a scale of 1/5. The model is rotated in water. Calculate the speed of rotation of the model necessary to simulate the rotation of the real disc. c) When the model is tested at 18.75 rpm, the torque was 0.02 N.m. Predict the torque on the full size disc at 200 rpm. Notes: For the oil: the density is 750kg/m² and the dynamic viscosity is 0.2 N.s/m². For water: the density is 1000 kg/ m² and the dynamic viscosity is 0.001 N.s/m². kg.m IN =1
Use the following TTT Diagram for the following questions: 800 A 1400 -Eutectoid temperature 700 1200 600 1000 500 800 400 600 300 Mistart) 200 50% 400 M+A M(50%) M(90%) 100 200 10-1 10 102 103 10 105 Time (s) Temperature ("C) Termperature (°F)
Show the COMPLETE SOLUTIONS including the derivation of formula and interpolations/extrapolations:NO Calculator Technique and Applications. 2. Steam at a pressure of 2.5 MPa is known to have a specific volume of 39.7x10-3 kg What is it specific enthalpy? 3. Your steam has a Data of 5.25 MPa and 395 C. Find v, u, h and s. 4. Your steam has a data of 4300 KPag and 362 °C, Find v, u, h and s.
The variables do not vary with respect to time is called as а. Static characteristics O b. Dynamic characteristics O c. Random Error d. Systematic Error
Give True or False for the following: 1.In liquids and gases, heat transmission is caused by conduction and convection 2.The surface geometry is the important factor in convection heat transfer 3. The heat transfer by conduction from heated surface to the adjacent layer of fluid, 4. The heat transfer is increased in the fin when &> 1 5.The unit of the thermal diffusivity is m²/s 6. Temperature change between the materials interfaces is attributed to the thermal contact resistance 7. A material that has a low heat capacity will have a large thermal diffusivity. 8. Heat conduction flowing from one side to other depends directly on thickness 9.Fin efficiency is the ratio of the fin heat dissipation with that of no fin 10.The critical radius is represented the ratio of the convicted heat transfer to the thermal conductivity
Saturated steam at 99.6 °C is heated to 350°C. Use the steam table provided to determine: a. The required heat input if 1 kg of steam undergoes the process in a variable-volume constant-pressure container. b. The work of expansion (in kJ) of the steam undergoing the process. C. The required heat input if a continuous stream flowing at 1 kg/s undergoes the process at constant pressure. d. Does your numeric answer to part c equal the sum of parts b and a? Explain why or why not. Given: 1 bar = 10 N/m4, Q= AH, Q = AU, AA = AÛ + PAV, table B.7 in kJ/kg and m/kg.
Ql: The viscosity in industrial measurement continue to use the CGS system of Lunits, since centimeters and grams vield convenient numbers for many fluids. The absolute viscosity () unit is the poise, I poise = 1 gtem. s). The kinematic viscosity (v) unit is the stohes, I stokes = 1 em /s. Water at 20C has u = 001 poise and also V= 0.01 stokes. Express these resalts in (a) SI and (h) BG tanits.
I1 Give an example how it is applied in molecular dynamics simulation and Monte carlo simulation? Typical distributions of particles in a volume (e.g. crystal structure for a solid, or distribution of masses and velocities in a “typical” galaxy) - Distributions of particle velocities/energies (e.g. Boltzmann distribution at a fixed temperature) - E.g. for a liquid it is common to start with a solid crystal structure and let the structure “melt” (by setting appropriate velocities corresponding to the liquid phase temperature!) - E.g. to setup a collision of two galaxies, you could try to generate a stable distribution of masses and velocities for a single galaxy first by performing a separate simulation -E.g. A simple model of a phase transition between a low temperature ordered phase (ferromagnet) and high temperature disordered phase (paramagnet) whats the difference in phase space in Molecular dynamics and Monte Carlo simulation?