Q(2) Complete the blank cells in the following table of properties of steam. In the last column describe the condition of steam as compressed liquid, saturated mixture, superheated vapor, or insufficient information; and, if applicable, give the quality. P (kpa) T ('C) v, m'/kg u, KJ/Kg Phase description 300 35 130.24 313.22 135 600 1.34139 275 0.500 600 3090

Q(2) Complete the blank cells in the following table of properties of steam. In the last column describe the condition of steam as compressed liquid, saturated mixture, superheated vapor, or insufficient information; and, if applicable, give the quality. P (kpa) T ('C) v, m'/kg u, KJ/Kg Phase description 300 35 130.24 313.22 135 600 1.34139 275 0.500 600 3090

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flat plate, maintained at 250 C is placed vertically in air at a pressure of 1 bar and temperature of 20 C. The plate height and width are 20 cm and 10 cm. Find the rate of heat transfer to this plate. [Ans.: 64 W].
Answer the last two parts of the question (d) the ideal gas properties of carbon monoxide table (Table A-21). Calculate the percent error between answers i) d & a, li) d & b and i) d & c.
Q8): To find how much heat is required to bring a kettle of water to its boiling point, you are asked to calculate the specific heat of water at 61°C. The specific heat of water is given as a function of time in Table below. Temperature, T Specific heat, C₂ (°C) J kg-°C 22 42 52 82 100 4181 4179 4186 4199 4217 Determine the value of the specific heat at 7=61°C using the direct T method of interpolation and a third order polynomial. Find the absolute relative approximate error for the third order polynomial approximation (Lagrange Method).
Water flow with a density of 998 kg / m3 at 70 ° C enters the system at a speed of 0.5 m / s and a 20 cm diameter pipe is pumped to a 2.5 m high reservoir with the help of a 7.5 kW pump. With the heater at the exit of the system, 1300 kW of energy is transferred to the water flow. Calculate the exit temperature of the water. (With reference to the height Z1, Z2 = 2.5 m is acceptable, ignore kinetic energy changes.) heater Pa pump and turbine P1 Ws reference plane O--
Density is defined as mass per unit volume (Fig. 1-25). Density: (kg/m) (1-4) The reciprocal of density is the specific volume v, which is defined as vol- ume per unit mass. That is, (1-5) For a differential volume element of mass ôm and volume &V, density can be expressed as P The density of a substance, in general, depends on temperature and pres- sure. The density of most gases is proportional to pressure and inversely proportional to temperature. Liquids and solids, on the other hand, are essentially incompressible substances, and the variation of their density with pressure is usually negligible. At 20°C, for example, the density of water changes from 998 kg/m' at I atm to 1003 kg/m' at 100 atm, a change of just 0.5 percent. The density of liquids and solids depends more strongly on temperature than it does on pressure. At I atm, for example, the density of water changes from 998 kg/m at 20°C to 975 kg/m at 75 C, a change of 2.3 percent, which can still be neglected in many…
Please help with homework as soon as you can.
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.
Complete the table below using steam tables. s (kJ/kg- K) h u Vх 103 t (oC) P (kPa) (kJ/kg) (kJ/kg) (m/kg) state 1 315 1431 80 3 380 2013.2 4 300 700 290 10000 6 300 859.6 7 17500 432.17 8 400 1000 9 250 300 10 340 518.7
just part d answer options are 1.8kJ 1.3J 1.3kJ 1.8J
A 2-kg steam water mixture at 1.0 MPaa is contained in an inflexible tank. Heat is added until the pressure rises to 3.5 MPaa and the temperature to 400 oC. Determine: a) Heat transferred (kJ), b) ΔH(kJ), c)ΔS (kJ/k) PLS PLS SHOW COMPLETE SOLUTION WRITE LEGIBLY AND ROUND OFF TO 4 DECIMALS INCLUDE P-S AND AND T-S DIAGRAMS PLS
In a power plant operating with water and steam, the following measurements and observations were done at various stages along the system. the pressure is 150 kPa and the enthalpy, h is 1580.115 (kJ/kg) For this case, the specific vvolume is most likely: 0.001070 2.01302 1.1594 0.5802 0.001053
calculate the saturation temperature