Submerged within a tank containing water and SAE 50 oil is solid sphere made from pinewood (SG = 0.38) and fastened with a thin cable to the bottom of the tank. What is thetension in cable AB if the sphere is submerged as shown? Hint: The volume of a sphere is(4/3)л³ where r is the radius. (a) If the cable AB is shortened, will the tension increase,decrease, or remain the same? Explain. (b) If the thickness of the oil layer is increased,will the tension increase, decrease, or remain the same? Explain.SAE 50 oilWater0.6mYAB1.0m

Answered: Image /qna-images/answer/14b0ed93-2649-461f-8815-e9a239406bed.jpg

Submerged within a tank containing water and SAE 50 oil is solid sphere made from pine wood (SG = 0.38) and fastened with a thin cable to the bottom of the tank. What is the tension in cable AB if the sphere is submerged as shown? Hint: The volume of a sphere is (4/3)³ where r is the radius. (a) If the cable AB is shortened, will the tension increase, decrease, or remain the same? Explain. (b) If the thickness of the oil layer is increased, will the tension increase, decrease, or remain the same? Explain. SAE 50 oil Water 0.6m B 1.0m

Submerged within a tank containing water and SAE 50 oil is solid sphere made from pine wood (SG = 0.38) and fastened with a thin cable to the bottom of the tank. What is the tension in cable AB if the sphere is submerged as shown? Hint: The volume of a sphere is (4/3)³ where r is the radius. (a) If the cable AB is shortened, will the tension increase, decrease, or remain the same? Explain. (b) If the thickness of the oil layer is increased, will the tension increase, decrease, or remain the same? Explain. SAE 50 oil Water 0.6m B 1.0m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the assembly shown. the block has a weight w = 200 lbs and the cord is attached to the pin at B. The pulleys have radi of rt = 2 Tn. and r2 1 În. Neglect the mass of the pulleys and the link. Pulley Pulley A 45 12 Compute the reaction at the ĩnk AB In lbs." 250 260 280 B.
The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Calculate the average normal strain developed in each wire. The wires are unstretched when the lever is in the horizontal position. A T 200 mm 200 mm B -300 mm- 200 mm D 300 mm E
The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. For the loading shown, determine: (a) the shaft deflection at pulley B. (b) the shaft deflection at pulley C. Assume P = 810 N, Q = 480 N, LAB = 260 mm, LBC = 400 mm
The 500 kN crate is supported by three cables as shown. Determine the tension in cable AD.
The homogeneous bar AB weighing 1800 lb is supported at either end by a steel cable. Calculate the smallest safe area of each cable if the working stress is 18 000 psi for steel. 2ft 1.5 ft a. 0.075 in? c. 0.100 in? d. 0.050 in? 5ft b. 0.128 in? Ans:
FN= 119, MN= 85, SN= 93
please answer question below step by step fill in all blanks v and m diagram fbd and final fbd
The steel pipe is filled with brass and subjected to a torsion T=34kNm. Determine each torsion value T, and T, taken by steel and brass. S Take the shear modulus for steel G,=80GPA and for brass G,=40GPA. T=34kNm cross-sect lon of A-B 2- steel 1- brass d,=12cm 100cm d;=4cm
2. The lap joint is fastened with four 30-mm-diameter rivets. The working stresses are 84 MPa for the rivets in shear and 84 MPa for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets... 35 mm KATIN 160 mm
Determine the shear lag factor of the connection shown in the figure. o o o o Answer:
2. Two 115-mm wide by 15-mm thick steel plates are welded as shown. The load P = 135 kN is concentrically applied and B= 25°. For the xy directions shown, determine a) b) The normal stress or acting perpendicular to the weld; The shear stress try' acting parallel to the weld; Sketch the state of stress to represent results from a) and b) above. В P 2² 115 mm. P
Please provide a detailed solution especiallyl for the moment of inertia and how you got the values etc. The book of Beer's manual solution does not provide a detailed solutino and it is hard to understand.