The steel pipe is filled with brass and subjected to a torsion T=34kNm.Determine each torsion value T, and T, taken by steel and brass.STake the shear modulus for steel G,=80GPA and for brass G,=40GPA.T=34kNmcross-sect lon of A-B2- steel1- brassd,=12cm100cmd;=4cm

Torsion: The twisting of an object due to the application of torque is known as Torsion. It is a…

The steel pipe is filled with brass and subjected to a torsion T=34kNm. Determine each torsion value T, and T, taken by steel and brass. Take the shear modulus for steel G,=80GPA and for brass G,=40GPA. T=34kNm cross-sect lon of A-B 2- steel 1- brass d,=12cm 100cm d;=4cm

The steel pipe is filled with brass and subjected to a torsion T=34kNm. Determine each torsion value T, and T, taken by steel and brass. Take the shear modulus for steel G,=80GPA and for brass G,=40GPA. T=34kNm cross-sect lon of A-B 2- steel 1- brass d,=12cm 100cm d;=4cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: ASSUME THAT THE TRUSS IS SIMPLY SUPPORTED AT JOINTS M AND E. Determine the stress at member CD if Pu…

A: Given data in question Area Length Dimensions Loading To find out Stress in member CD Note We…

Q: E Bars AB CD are rigid. The supports are pins at A and C and the Steel. What maximum force P can be…

A: Maximum force P

Q: Compute for the linear weight of 10 mm reinforcing bar. (Use the unit weight of the Steel). o 0.692…

A: Given data in question Diameter Steel bar To find out Linear weight Note Unit weight of steel =…

Q: A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness…

Q: Problem 3: The rectangular bars shows are in tension and are joined together by two bolts as shown.…

A: Given data : Load=P P=20 kips Diameter of bolt (d)=38 in Required : Shear stress

Q: From the figure below, determine member BD

A: Force in the vertical direction - RA + RC = 0 Sum of the moment at the point C- ∑MC = 0⇒-RA×8 +…

Q: Determine: a. Cross sectional area of the members b. Internal load in member AB, and indicate if…

A: a. Cross-sectional area of the members Since each member has a semi-circular cross-section with a…

Q: A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and six…

A: Step 1: Calculate the shear area per bolt: Steel bolts: A = π * (12 / 2)2 = 113.1 mm2 Aluminum…

Q: (1) A L1 B (2) L2 C L3 (3) D

Q: Determine: a. Cross-sectional area of the members b. Internal load in member AB, and indicate if…

Q: For the connection shown, the bolt diameter is d = 15 mm. The average shear stress in the bolts…

Q: An aluminum alloy [E = 10,000 ksi; σY = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

A: Given data: pipe 1: (aluminum) outside diameter = 2.3 in wall thickness = 0.21 in Length = 7 ft E =…

Q: Solve the plate shown in the figure, Include fbd on solutions

Q: PART 2 : COMPUTE THE AXIAL STRESSES IN ALL MEMBERS OF THE TRUSS SHOWN. USE 300 sq. mm AND 250 sq. mm…

A: Question is based on truss supported on roller and hinged support. Span length of member and loading…

Q: Knowing that P=(4a) kN, Tallow.=60 MPa, Oallow.compressive =140 MPa, a) Find the diameter (d) of the…

A: It is Given that, P = 42 KN ( as it is Mentioned in the Question) Allowable Tensile…

Q: Problem 2: A bar is made from bonded pieces of steel (E = 29x10 psi) and brass (E = 15x10 psi).…

A: Given : Es = 29 X 106 psi Eb = 15 X 106 Determine the max. stress in the steel and brass when a…

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: Yield Strength : Yield strength of an element is a maximum stress an element or component can bear…

Q: An aluminum alloy [E = 10,000 ksi; σy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

Q: A force P = 85 kN is applied at the plate-bolt connection shown. Determine the required diameter in…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Determine the nominal strength for tensile yielding in the gross section. 1. B. 429.67 KN D.390.10…

Q: Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum…

A: Given that: E = 200 GPa

Q: the

A: A device for measuring corneal thickness that is installed on a slit-lamp is known as pachometer. It…

Q: Check the slenderness of the steel section against Local Buckling.

A: We know that for flexure sections are classified as compact, non compact and slender sections For a…

Q: The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed…

Q: 15 Flad the ABE GO Kri CD = 70 ksi BC - 50 ksi 0.4 in2 4. 0.3 n? 4P- 3p P4

Q: two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm.…

A: Find modular ratio:n=EwEs=40200=15so,Reduced width of wood =1505=30mmFInd…

Q: Q2:If allowable stresses are at = max. value of W. W 2m 8m 165MPa, oc = 100MPa t = 70MPa determine…

Q: An aluminum alloy [E = 10,000 ksi; Oy = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

A: Given, The Aluminum alloy, Modulus of Elasticity of aluminum, E1=10000 Ksi. Modulus of Elasticity of…

Q: or the beam shown, determine the stress in each rod if the load P= 50 kN is applied. Bronze Steel…

Q: The safety stress for the steel bar shown in the figure is σallow= 160MPa. According to the greatest…

A: Solution:

Q: B 3 m 3 m 4 m E C D 50 KN 80 KN 4 m F licate if

Q: The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of…

Q: AB kN AC kN 3. Simply supported beam with rectangular section is subjected to the loads shown in the…

A: Finding out normal stresses.

Q: A sheet of copper is stretched bi-axially in the xy-plane. If the strains in the sheets are Ex=0.40…

Q: An aluminum alloy [E = 10,000 ksi; σY = 40 ksi] pipe (1) is connected to a bronze [E = 16,000 ksi;…

Q: Part 5 Find the force in the steel tube (1), F₁, and the forces F₂ and F3, which are the forces in…

A: Given Outside diameter= 3.50 in

Q: Cm 4m 4m Gom G Gm. F Gm 76 KN 14 76 KN

Q: J- A T beam supports the three concentrated loads shawn. Öctermine the merximum tensile 1.41 KN 5.64…

Q: Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined ogether by a pin…

A: thickness =35mm Width =160mm Length =200mm Pin Diameter =60mm

Q: For the exact in the figure tensile strength = 8000 N/cm^2 compression safety = 3000 N/cm^2…

A: Allowable tensile strength is given as:Allowable compressive strength is given as:

Q: The built-up member shown is subjected to Pa=155k. KLX= 17.5ft, KLy=10ft and Fy=36ksi. a-Choose the…

A: given; Pa = 155 K KLX = 17.5 ft. KLY= 10 ft. Fy = 36 ksi Assume KLr = 60

Q: 5 4 all 5 4 #9 4 24- 16" £3" ft-k fé = 3 ksi M = 90 NWC. The section is cracked. Computer the…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

The steel pipe is filled with brass and subjected to a torsion T=34kNm.
Determine each torsion value T, and T, taken by steel and brass.
S
Take the shear modulus for steel G,=80GPA and for brass G,=40GPA.
T=34kNm
cross-sect lon of A-B
2- steel
1- brass
d,=12cm
100cm
d;=4cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

only HANDWRITTEN answer needed ( NOT TYPED)
From Steel Design Topic Include complete solution
Calculate the shear stress in MPa at section B A 100 mm F-10EN 10 mm
3. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc-20.70 MPa. In checking whether steel yields or not, the value of "fs" is__ _MPa. 1644.056 1302.491 1935.087 2402.455 O2735.802 O 3014.642 Other:
4
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 L3=1350 GPa. L2=2150 A L1 E Dia. 1 L1=1350 Р3-25 P1 L2 Dia. 2 P2=40 P2 P1=105 Dia2=45 L3 P3 D D 35 mm o Dia1=60
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
Check the slenderness of the steel section against Local Buckling. 340 mm Use Fy = 800 MPa. O Compact Slender I O Adequate 400 mm None of the choices 30 mm 20 mm 20 mm
The AD beam, which is fixed at left end, is under various loads as shown below. a) Draw internal load diagrams (Nx, Vy, M2) using the method of section. b) Determine the state of stress at points G, H and I for section B. c) For the corresponding points, indicate the results (i.e. stress components) on a differential element. b2 A B G М F2 2l h bi GIVEN DATA: Fo = 10000 N, F1 1200 N, F2 = 1000 N, qo = 50 N/cm, Mo = 50000 Nem, l = 25 cm bi = 10 cm, b2 = 20 cm, h 12 cm, t 1 cm
*4-76 The C83400-red-brass rod AB and 2014-T6-alu- minum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T₁ = 50°F, determine the average normal stress in each member when T₂ = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in². 3 ft B 2 ft C
Find the allowable bending stress for the following shapes. Assume adequate lateral support for the compression flange. a.) W30 x132 of A36 Steel
The lap joint of a tension member is shown. The plate is 252 mm wide and 12 mm thick. The bolts are 20 mm in diameter and the holes are 3 mm larger than the bolt diameter. Use A36 steel. a. Determine the safe value of P based on tension net area. b. Determine the safe value of P based on tension bearing failure. c. Determine the safe value of P based on tension block shear.