Subjact:Data:An inverted u tube manometer is connected to two horizontal pipes A.and 8 threugh which water is flowing The vertical distance betweenaxes of the se pipes is30 cM When an oil SG=0.8 îs uced as aJauge fluid, the vertical heigh 1s ofwater columos in the two limbs arefound to be the sameand equal to 35 cm. Determine the differenceOf pressure between thepipes.0.8Sp.gr.C.30 cm35 cm35cmtw ater30cmwater

Subjact: Data: An inverted u tube manometer is connected to two horizontal pipes A and B through which water is flowing The vertical distance between axes of these pipes is 30 CM When an oil SG 0.8 îs uced as a gauge fluid, the vertical heights af water columns in the two limbs are found to be the same and equal t0 35 cm. Determine the difference Of pressure between the pipes. 0.8 Sp.gr. 30 cm 35 cm 35cm to ater 30 cm water

Subjact: Data: An inverted u tube manometer is connected to two horizontal pipes A and B through which water is flowing The vertical distance between axes of these pipes is 30 CM When an oil SG 0.8 îs uced as a gauge fluid, the vertical heights af water columns in the two limbs are found to be the same and equal t0 35 cm. Determine the difference Of pressure between the pipes. 0.8 Sp.gr. 30 cm 35 cm 35cm to ater 30 cm water

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question: Cd= 1:0 = 0=1cm @ Derive The Equation Of Motion In Terms Of Height 2 Time For... Cd-1:0 D=I cm DeriDe the caationo Motirn in terms o height Tme Sor empgtng the tank Pen 1om 5m
What is the difference between the pressure at the two sections? * :A horizontal pipe , I P4 in diameter, taperv gradually to 8 in. in dia meter. If the flow ir 500 cu f4 of water per minute, what i the difference between the presure at the two sections? Given : Quyo ® 500 ft³/min do 8" O 445.66 psf O 417.65 psf O 455.89 psf O 420.11 psf O 432.37 psf
Determine the viscosity of fluid between shaft e 2 - sleeve shown in fiqure below Assump linear velocity distri bution. 200mum fluid Aus. : 1.183 pa.s V=o.12 89N A> const. velaity 7 Sum dia
Q2) i Neglecting minor losses in the pipe, determine the flows in the pipes and 0 the pressure heads at the nodes (kinematic viscosity= 1.13x104m?¥s) F E n I I 30 Data Pipe Ab BC O DE EF AF BE Lengeh (m) 600 600 200 600 600 200 200 Diameter (wm) 250 150 100 150 150 200 100 Roughness size of all pipes = 0.06 mm Pressure head elevation at A = 70 i o.d. Elevation of pipe nodes A 5 c D L ® 028 0 20 2 2
A circular orifice of 50 mmdiameter is fixed to the end of a water pipe of 75mm diameter. The gauge pressure in the pipe is70 kPa. The flow out of theorifice was measured as0.017 m^3/second. Theactual jet velocity wasmeasured by pitot tubewith a value of 12 m/s.a. Determine Cv, Cc and Cd.b. Calculate the head loss.
loving to another question will save this response. con 37 A pressure gage 10.82 m. above the bottom of a tank containing a liquid reads 58.09 kPa; another gage at height 3.39 m. reads 83.33 kPa. Determine the density of the liquid. Round off to three decimal places. A Moving to another question will save this response. «< Question 37 of 48 1SUS DELETE Ans nCr OFF W W 3. ue OON SNI DEL
PROBLEM: The discharge of the pipe system shown is 420 liters/sec, Deter- mine the head loss from A to D. Assume f = 0.020 30mmo; GOO m 750 mmo; 900 250 mm d; 450 m GOo mm 6; 1200m 3 Solution 375 mma; 750 m 0 0826 10
This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. What will be the gage pressure reading at A? correction: 3.75 mm should be 375 mm en Me Do not write the unit. You will only input the numerikal answer in the space provided. Unit of the Correct Answer. kPa Decimal Places required in the firal answer 3
Theflowrateofwaterthroughacastironpipeis5000GPM.The diameter of the pipe is 330mm, and the coefficient of friction is f=0.0173. What is the pressure drop over a 30m length of pipe
7) For the manometer setup shown, determine the difference in pressure between A and B. oll, s = 0.85 Water 680 mm Bo 1700 mm YWater 8) A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B. is h. 100 mm re A Mercury A B Oil, s = 0.90 %3!
Hydrostatic pressure center Q\ complete the following table Tilt angle ( a ) Lowest water level Highest (sh)mm (St) mm 0 0 100 Level Weight Water Calculated Calculated FG.L FP.LD arm (FG)N level (LD)mm (FP)N (N.mm) (N.mm) L(mm) (s)mm 250 1.5 72.2 250 2.0 80.5 250 2.5 91 b= 75 (mm) y =9810 (N/m³) Calibration of pressure gauge Q\ Draw and mention the parts of the application? Orifice and jet trajectory test Q\ Determine the objective of the experiment then define the hydraulic bench?
the unknown fluid? Express your answer in Ib/ft³. TEST 1 Fall 2021 5. For the configuration shown in the figure below what must be the value of the unit weight of the upkontiguration shown in the fiqure below what must be the value of the unit weight of ie unknown fluid? Express your answer in Ib/t. [Max. 10 Points] Open Water 49 in 5.5 in 3.3in JAknown 1.4tin